Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 6
items per page: 25 50 75
Sort by:

Abstract

Rice blast is one of the most destructive rice diseases known to cause considerable yield losses globally. Plant growth promoting rhizobacteria (PGPR) and arbuscular mycorrhizal fungi (AMF) are closely associated with rice plants and improve plant growth and health. To determine how isolated bacteria trigger rice growth, an assessment of phosphate solubilization and auxin production mechanisms was carried out in vitro and in vivo. In this study, the interactions between PGPR and Rhizophagus irregularis were evaluated in wildtype and CYCLOPS mutant plants to provide a sustainable solution against blast disease and reduce the amount of yield loss. Importantly, Bacillus subtilis UTSP40 and Pseudomonas fluorescens UTSP50 exhibited a suppressive effect on AMF colonization which shows the probable existence of a functional competition between AMF and PGPR to dominate the rhizosphere. On the other hand, R. irregularis decreased the biocontrol activity of B. subtilis UTSP40 in wild type, although this reduction was not significant in mutant plants. Results showed that the same defense-related genes were induced in the roots of wild type colonized by B. subtilis UTSP40 and R. irregularis. Therefore, plant cell programs may be shared during root colonization by these two groups of beneficial microorganisms.
Go to article

Abstract

Air abrasion process is used for cleaning casting surface of prosthetic components, and to prepare the surface of these elements for the application of veneering items. Its side effect, however, is that abrasive particles are embedded in the treated surface, which can be up to 30% of the surface and it constitutes the side effect of this procedure. Such a significant participation of foreign material can not be indifferent to the properties of the surface. Embedded particles can be the place of stress concentration causing cracking of ceramics, and may deteriorate corrosion resistance by forming corrosive microlinks. In the latter cases, it would be advisable to remove elements embedded into the surface. The simplest method is chemical etching or electrochemical one. Nevertheless, these procedures should not significantly change the parameters of the surface. Among many possible reagents only a few fulfills all the above conditions. In addition, processing should not impair corrosion resistance of titanium, which is one of the most important factors determining its use as a prosthetic restoration in the mouth. The study presented results of corrosion resistance of titanium used to make prosthetic components by means of casting method, which were subjected to chemical processing designed to remove the embedded abrasive particles. The aim of the study was to investigate whether etching with selected reagents affects the corrosion resistance of titanium castings. For etching the following reagents were used: 30% HNO3 + 3% HF + H2O, HNO3+ HF+ glycerol (1:2:3), 4% HF in H2O2, 4% HF in H2O, with a control sandblasted sample, not subjected to etching. Tests demonstrated that the etching affected corrosion properties of test samples, in each case the reduction of the corrosion potential occurred - possibly due to the removal of particles of Al2O3 from the surface and activation of the surface. None of the samples underwent pitting corrosion as a result of polarization to 9 V. Values of the polarization resistance, and potentiodynamic characteristics indicated that the best corrosion resistance exhibited the samples after etching in a mixture of 4% solution of HF in H2O2. They showed very good passivation of the surface.
Go to article

Abstract

The major downside of blasting works is blast vibrations. Extensive research has been done on the subject and many predictors, estimating Peak Particle Velocity (PPV), were published till date. However, they are either site specific or global (unified model regardless of geology) and can give more of a guideline than exact data to use. Moreover, the model itself among other factors highly depends on positioning of vibration monitoring instruments. When fitting of experimental data with best fit curve and 95% confidence line, the equation is valid only for the scaled distance (SD) range used for fitting. Extrapolation outside of this range gives erroneous results. Therefore, using the specific prediction model, to predetermine optimal positioning of vibration monitoring instruments has been verified to be crucial. The results show that vibration monitoring instruments positioned at a predetermined distance from the source of the blast give more reliable data for further calculations than those positioned outside of a calculated range. This paper gives recommendation for vibration monitoring instruments positioning during test blast on any new site, to optimize charge weight per delay for future blasting works without increasing possibility of damaging surrounding structures.
Go to article

Abstract

One of the main purpose of accurate blasting in open pit mining is to achieve optimum rock fragmentation. The degree of rock fragmentation plays a significant role in order to control and minimise the overall production cost including loading, hauling and crushing. In the present paper, the application of a Number-Size (N-S) fractal model is intended to classify the blast fragmentation size in the Jalal-Abad iron mine, SW Iran, using GoldSize image analysis software for four blasting with the obtained result being compared with Kuz-Ram curves. To do this, the fractal dimensions via N-S log-log plots were generated based on the output of the GoldSize software. The results indicated that the fragmented rocks have a multifractal nature with four/five different fragmented populations in terms of size namely; the fine rocks with the size of less than 16 cm, Mean-fragment values between 16 and 45 cm, In-range between 45 and 70 cm and finally, oversize larger than 70 cm.
Go to article

Abstract

Shot blasting machines are widely used for automated surface treatment and finishing of castings. In shot blasting processes the stream of shots is generated and shaped by blasting turbines, making up a kinetic and dynamic system comprising a separating rotor, an adapting sleeve and a propelling rotor provided with blades. The shot blasting performance- i.e. the quality of shot treated surfaces depends on the actual design and operational parameters of the unit whilst the values of relevant parameters are associated with the geometry of turbine components and the level of its integration with the separator system. The circulation of the blasting medium becomes the integrating factor of the process line, starting from the hopper, through the propeller turbine, casting treatment, separation of contaminated abrasive mixture, to its recycling and reuse. Inferior quality of the abrasive agent (shot) and insufficient purity of the abrasive mixture are responsible for low effectiveness of shot blasting. However, most practitioners fail to fully recognize the importance of proper diagnostics of the shot blasting process in industrial conditions. The wearing of major machine components and of the blasting agent and quality of shot treated surfaces are often misinterpreted, hence the need to take into account all factors involved in the process within the frame of a comprehensive methodology. This paper is an attempt to formulate and apply the available testing methods to the engineering practice in industrial conditions.
Go to article

This page uses 'cookies'. Learn more