The paper presents the effect of manganese on the crystallization process, microstructure and selected properties: cast iron hardness as well as ferrite and pearlite microhardness. The compacted graphite was obtained by Inmold technology. The lack of significant effect on the temperature of the eutectic transformation was demonstrated. On the other hand, a significant reduction in the eutectoid transformation temperature with increasing manganese concentration has been shown. The effect of manganese on microstructure of cast iron with compacted graphite considering casting wall thickness was investigated and described. The nomograms describing the microstructure of compacted graphite iron versus manganese concentration were developed. The effect of manganese on the hardness of cast iron and microhardness of ferrite and pearlite were given.
This paper presents numerical simulationsof the behavior of a sandy layer subjected to a cyclic horizontal acceleration in shaking table tests, with a particular attention focused on the settlements of a dry sand layer, and on the liquefaction of saturated sand. A compaction/liquefaction model (C/L) is applied to these simulations. The infl uence of specifi c parameters of the model on the compaction and liquefaction of a sandy layer is shown and discussed. The results of simulations are compared with selected experimental data.
The compactness of dimension stone blocks was previously controlled through various methods that were partially based on personal experiences, acoustic and visual observance of materials. With the development of technology, the ultrasonic pulse method is frequently used for the examination of stone test pieces and with an analysis of acquired data through the tomography method, the compactness is determined. The monolith stone blocks that are found at a site contain hidden discontinuities. The technique of data acquisition and the use of various instruments enable a good overview of the block interior. With an increased number of measurements, a suitable classification is prepared that helps reduce modification costs and increases the quality of stone blocks. The control methodology of compactness is based on the passage of longitudinal waves through the stone block without damaging the block during control. High differences in speed show irregularities in the material. With the observation system, we can prepare a tomography of the measured profiles that show us the locations of irregularities that should be observed more closely. During in situ measurements, the data for comparison with measured results are acquired. Determination of critical locations is of extreme importance before the processing of the block into smaller stone products or during the reconstruction of older stone elements or sculptures. The purpose of “in situ” measurements is to prepare a simple and fast method for the evaluation of materials compactness and for production work.
The Antarctic Peninsula region has experienced a recent cooling for about 15 years since the beginning of the 21st century. In Livingston Island, this cooling has been of 0.8°C over the 12-yr period 2004–2016, and of 1.0°C for the summer average temperatures over the same period. In this paper, we analyse whether this observed cooling has implied a significant change in the density of the snowpack covering Hurd and Johnsons glaciers, and whether such a density change has had, by itself, a noticeable impact in the calculated surface mass balance. Our results indicate a decrease in the snow density by 22 kg m-3 over the study period. The density changes are shown to be correlated with the summer temperature changes. We show that this observed decrease in density does not have an appreciable effect on the calculated surface mass balance, as the corresponding changes are below the usual error range of the surface mass balance estimates. This relieves us from the need of detailed and time-consuming snow density measurements at every mass-balance campaign.
The objective of the present research is to develop the novel multi-compaction technology to produce hybrid structure in powder metallurgy (P/M) components using dissimilar Fe-based alloys. Two distinct powder alloys with different compositions were are used in this study: Fe-Cr-Mo-C pre-alloyed powder for high strength and Fe-Cu-C mixed powder for enhanced machinability and lower material cost. Initially, Fe-Cu-C was pre-compacted using a bar-shaped die with lower compaction pressure. The green compact of Fe-Cu-C alloy was inserted into a die residing a half of the die, and another half of the die was filled with the Fe-Cr-Mo-C powder. Then they subsequently underwent re-compaction with higher pressure. The final compact was sintered at 1120°C for 60 min. In order to determine the mechanical behavior, transverse rupture strength (TRS) and Vickers hardness of sintered materials were measured and correlated with density variations. The microstructure was characterized using optical microscope and scanning electron microscope to investigate the interfacial characteristics between dissimilar P/M alloys.
The use of fly ash as a material for earth structures involves its proper compaction. Fly ash compaction tests have to be conducted on separately prepared virgin samples because spherical ash grains are crushed during compaction, so the laboratory compaction procedure is time-consuming and laborious. The aim of the study was to determine the neural models for prediction of fly ash compaction curve shapes. The attempt of applying the artificial neural networks type MLP was made. ANN inputs were new-created variables – principal components dependent on grain-size distribution (as D₁₀–D₉₀ and uniformity and curvature coefficients), compaction method, and fly ash specific density. The output vectors were presented by co-ordinates of generated compaction curve points. Each point (wᵢ, ρdi) was described by two independent ANNs. Using ANN-based modelling method, models which enable establishing the approximate compaction curve shape were obtained.
The Szamotuły Graben covers the southernmost part of the Permo-Mesozoic Poznań–Szamotuły Fault Zone. Along this regional discontinuity there are several salt structures, including the Szamotuły diapir, over which an extensional graben formed in the Paleogene and Neogene. The graben is located north of Poznań in central- western Poland, and is NW–SE-trending, ~20 km long, 3–5.5 km wide, and up to 160 m deep. It is filled with Lower Oligocene and Neogene sediments, including relatively thick lignite seams. Data from boreholes allow the assignment of the graben-fill sediments to appropriate lithostratigraphic units. Furthermore, analysis of changes in the thickness of these units provides evidence for periods of accelerated graben subsidence or uplift relative to its flanks. As a result, two distinct stages of tectonic subsidence and one inversion in the Paleogene–Neogene evolution of the Szamotuły Graben have been distinguished. Thus, relatively significant subsidence occurred in the Early Oligocene and the middle Early–earliest Mid-Miocene, while slight inversion took place in the middle part of the Mid-Miocene.
The article is devoted to the method facilitating the diagnostics of dynamic faults in networks of interconnection in systems-on-chips. It shows how to reconstruct the erroneous test response sequence coming from the faulty connection based on the set of signatures obtained as a result of multiple compaction of this sequence in the MISR register with programmable feedback. The Chinese reminder theorem is used for this purpose. The article analyzes in detail the various hardware realizations of the discussed method. The testing time associated with each proposed solution was also estimated. Presented method can be used with any type of test sequence and test pattern generator. It is also easily scalable to any number of nets in the network of interconnections. Moreover, it supports finding a trade-off between area overhead and testing time.
Achieving control of coating thickness in foundry moulds is needed in order to guarantee uniform properties of the mould but also to achieve control of drying time. Since drying time of water based coatings is heavily dependent on the amount of water present in the coating layer, a stable coating process is prerequisite for a stable drying process. In this study, we analyse the effect of different variables on the coating layer properties. We start by considering four critical variables identified in a previous study such as sand compaction, coating density, dipping time and gravity and then we add centre points to the original experimental plans to identify possible non-linear effects and variation in process stability. Finally, we investigate the relation between coating penetration (a variable that is relatively simple to measure in production) and other coating layer thickness properties (relevant for the drying process design). Correlations are found and equations are provided. In particular it is found that water thickness can be directly correlated to penetration with a simple linear equation and without the need to account for other variables.