Modern regulations concerning railway bridges are based on the approach of structural dynamics, which is described in PN-EN standards. This paper presents the results of theoretical dynamic analysis of the HSLM-A train set loading on the structure of a pre-stressed concrete arch bridge - the first railway bridge of its type which was built in Poland (completed in 1959). The recommendations of PN-EN have been followed and modal analysis was carried out to define the sensitivity of the structure to chosen eigenforms. Additionally the paper presents a course of calculations and the conclusions obtained from the analysis of displacements, accelerations, and bending moments induced in the structure through a simulated passage of a high-speed train in the context of the requirements of PN-EN Standards. The conclusions from the current calculations can be used for dynamic analysis of bridges of similar structural solutions.
Considering concrete nonlinearity, the wave height limit between small and large amplitude sloshing is defined based on the Bernoulli equation. Based on Navier-Stokes equations, the mathematical model of large amplitude sloshing is established for a Concrete Rectangle Liquid-Storage Structure (CRLSS). The results show that the seismic response of a CRLSS increases with the increase of seismic intensity. Under different seismic fortification intensities, the change in trend of wave height, wallboard displacement, and stress are the same, but the amplitudes are not. The areas of stress concentration appear mainly at the connections between the wallboards, and the connections between the wallboard and the bottom.
The paper presents dynamic responses of annular plate composed of three layers. The middle layer of the plate has electrorheological properties expressed by the Bingham body model. The plate is loaded in the plane of facings with time-dependent forces. The electrorheological effect is observed in the area of supercritical plate behaviour. The influence of both material properties and geometrical dimensions of the core on plate behaviour is examined. The problem is solved analytically and numerically using the orthogonalization method and the finite difference method. Comparison of the results obtained using the finite difference and the finite element methods for a plate in critical state is shown. The numerical calculations are carried out for axisymmetric and asymmetric plate modes. The presented diagrams show the plate reaction to the changes in values of plate parameters and indicate that the supercritical control of plate work is possible.
An array consisting of four commercial gas sensors with target specifications for hydrocarbons, ammonia, alcohol, explosive gases has been constructed and tested. The sensors in the array operate in the dynamic mode upon the temperature modulation from 350°C to 500°C. Changes in the sensor operating temperature lead to distinct resistance responses affected by the gas type, its concentration and the humidity level. The measurements are performed upon various hydrogen (17-3000 ppm), methane (167-3000 ppm) and propane (167-3000 ppm) concentrations at relative humidity levels of 0-75%RH. The measured dynamic response signals are further processed with the Discrete Fourier Transform. Absolute values of the dc component and the first five harmonics of each sensor are analysed by a feed-forward back-propagation neural network. The ultimate aim of this research is to achieve a reliable hydrogen detection despite an interference of the humidity and residual gases.
The model considered in the paper is defined as VAR with the prior distribution for parameters generated by the dynamic stochastic general equilibrium (DSGE) model. The degree of economic restrictions in the DSGE-VAR model is controlled by the weighting parameter. In the paper there is investigated the impact of the weighting parameter prior specifications for the posterior shape of impulse response functions (IRFs). In case of conditional models the paths of IRFs highly depend on the value of the weighting parameter that is set arbitrary. When considering full estimation with different prior types, means and gradual change in the dispersion the posterior time paths of IRFs are similar in models with high values of the marginal data density.
A method for evaluating the dynamic characteristics of force transducers against small and short-duration impact forces is developed. In this method, a small mass collides with a force transducer and the impact force is measured with high accuracy as the inertial force of the mass. A pneumatic linear bearing is used to achieve linear motion with sufficiently small friction acting on the mass, which is the moving part of the bearing. Small and short-duration impact forces with a maximum impact force of approximately 5 N and minimum half-value width of approximately 1 ms are applied to a force transducer and the impulse responses are evaluated.
Sensitivity analysis of the dynamic response of both the designed and the actual models of a slewing superstructure with two masts to the variation of the counterweight mass and the degree of accuracy of the approximation polynomials of the digging resistance was conducted in the paper. Spatial reduced dynamic models of the bucket wheel excavator SchRs 1600 were used as a basis for the presented investigations. Based on the comparative analysis of the calculation results, the following conclusions were drawn: (a) mass of the counterweight has a significantly higher influence on the maximum intensities of accelerations of the referent points than on the spectrum of natural frequencies, (b) the accuracy of approximations of the digging resistance and the maximum values of accelerations differ by an order of magnitude, for the approximation trigonometric polynomial of the same number of harmonics.