Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 7
items per page: 25 50 75
Sort by:

Abstract

The paper presents the results of investigations concerning the influence of gray cast iron modification on free vibration frequency of the disc casting. Three different chemical composition melts of gray cast iron were prepared in induction furnace. During gravity casting 0.05% and 0.3% mass of the Inolate modifier was added on stream of metal for changing graphite flakes in castings. Sound signal vibration of cast iron sample was registered by means on microphone for free vibration frequency measurements. Decreasing of free vibration frequency of modified cast iron in comparison with non modified castings was observed. Higher contents of modifier causes more decreasing of free vibration frequency. Cast iron with smaller contents of carbon and silicon have higher free vibration frequency in comparison with eutectic composition cast iron. Hardness of examined cast iron is lower when the more modifier is added during modification process. Free frequency is smaller with smaller Brinell hardness of disc casting. It was concluded that control of free vibration frequency of disc castings by means of chemical composition and modification process can improved comfort and safety of working parts.
Go to article

Abstract

Two fundamental challenges in investigation of nonlinear behavior of cantilever beam are the reliability of developed theory in facing with the reality and selecting the proper assumptions for solving the theory-provided equation. In this study, one of the most applicable theory and assumption for analyzing the nonlinear behavior of the cantilever beam is examined analytically and experimentally. The theory is concerned with the slender inextensible cantilever beam with large deformation nonlinearity, and the assumption is using the first-mode discretization in dealing with the partial differential equation provided by the theory. In the analytical study, firstly the equation of motion is derived based on the theory of large deformable inextensible beam. Then, the partial differential equation of motion is discretized using the Galerkin method via the assumption of the first mode. An exact solution to the obtained nonlinear ordinary differential equation is developed, because the available semi analytical and approximated methods, due to their limitations, are not always sufficiently reliable. Finally, an experiment set-up is developed to measure the nonlinear frequency of oscillations of an aluminum beam within a domain of initial displacement. The results show that the proposed analytical method has excellent convergence with experimental data.
Go to article

Abstract

In this paper, a semi-analytical solution for free vibration differential equations of curved girders is proposed based on their mathematical properties and vibration characteristics. The solutions of in-plane vibration differential equations are classified into two cases: one only considers variable separation of non-longitudinal vibration, while the other is a synthesis method addressing both longitudinal and non-longitudinal vibrationusing Rayleigh’s modal assumption and variable separation method. A similar approach is employed for the out-of-plane vibration, but further mathematical operations are conducted to incorporate the coupling effect of bending and twisting. In this case study, the natural frequencies of a curved girder under different boundary conditions are obtained using the two proposed methods, respectively. The results are compared with those from the finite element analysis (FEA) and results show good convergence.
Go to article

Abstract

In this paper, nonlinear free vibration analysis of micro-beams resting on the viscoelastic foundation is investigated by the use of the modified couple stress theory, which is able to capture the size effects for structures in micron and sub-micron scales. To this aim, the gov-erning equation of motion and the boundary conditions are derived using the Euler–Bernoulli beam and the Hamilton’s principle. The Galerkin method is employed to solve the governing nonlinear differential equation and obtain the frequency-amplitude algebraic equation. Final-ly, the effects of different parameters, such as the mode number, aspect ratio of length to height, the normalized length scale parameter and foundation parameters on the natural fre-quency-amplitude curves of doubly simply supported beams are studied.
Go to article

Abstract

Complex structures used in various engineering applications are made up of simple structural members like beams, plates and shells. The fundamental frequency is absolutely essential in determining the response of these structural elements subjected to the dynamic loads. However, for short beams, one has to consider the effect of shear deformation and rotary inertia in order to evaluate their fundamental linear frequencies. In this paper, the authors developed a Coupled Displacement Field method where the number of undetermined coefficients 2n existing in the classical Rayleigh-Ritz method are reduced to n, which significantly simplifies the procedure to obtain the analytical solution. This is accomplished by using a coupling equation derived from the static equilibrium of the shear flexible structural element. In this paper, the free vibration behaviour in terms of slenderness ratio and foundation parameters have been derived for the most practically used shear flexible uniform Timoshenko Hinged-Hinged, Clamped-Clamped beams resting on Pasternak foundation. The findings obtained by the present Coupled Displacement Field Method are compared with the existing literature wherever possible and the agreement is good.
Go to article

Abstract

In this paper, thermally-excited, lateral free vibration analysis of a small-sized Euler-Bernoulli beam is studied based on the nonlocal theory. Nonlocal effect is exerted into analysis utilizing differential constitutive model of Eringen. This model is suitable for design of sensors and actuators in dimensions of micron and submicron. Sudden temperature rise conducted through the thickness direction of the beam causes thermal stresses and makes thermo-mechanical properties to vary. This temperature field is supposed to be constant in the lateral direction. Temperatures of the top and bottom surfaces of the system are considered to be equal to each other. Governing equation of motion is derived using Hamilton’s principle. Numerical analysis of the system is performed by Galerkin’s approach. For verification of the present results, comparison between the obtained results and those of benchmark is reported. Numerical results demonstrate that dynamic behavior of small-sized system is been effected by temperature shift, nonlocal parameter, and slenderness ratio. As a result, taking the mentioned parameters into account leads to better and more reliable design in miniaturized-based industries.
Go to article

This page uses 'cookies'. Learn more