Lighting sources with a cold cathode are widely used in electronics. The lamps with a cold cathode are used primarily as sources of white light in optical scanners, digital indicators, display panels and signalling devices. In the paper the advantages of carbonaceous materials as emitters of cold electrons and the possibilities of using them to create a cathode in an electron lamp are discussed.
The occurrence of a hydraulic connection between piezometers is identified based on similar changes in water levels. Some piezometers react to changing upper or lower water levels, some may also react to atmospheric precipitation. If the reaction to variable upper water levels is significant, then leakage of seepage control devices is identified and the dam is subjected to repair works. The aim of this research paper is to present and analyse the dynamics of variability of water lev-els in open piezometers of the Chańcza dam, located at the 36 km of the Czarna Staszowska River in the town of Korytnica in Świętokrzyskie province (Poland). Before the analysis of the piezometric data was commenced, the Grubbs statistical test was used to identify and reject the outliers. The scope of the research includes the data captured between January 14, 2014 and January 13, 2017. A hypothesis was formulated that the change in the trend occurred after the spring of 2015 when the water level in the reservoir was reduced by approx. 1.5 m. Two trend lines were adapted for the water levels of each pie-zometer using the least squares method – the first one for the period from January 2014 to May 2015, and the second one from June 2015 to January 2017. In this way, two slopes of the linear function were obtained together with an estimation of their errors. These slopes were compared using a statistical parallelism test.
The study evaluated the curing properties of natural silica sand moulded with 1% by weight Furotec 132 resin binder catalysed by Furocure CH Fast acid and Furocure CH Slow acid. Physical properties of this sand included an AFS number of 47.35, 4.40 % clay, 0 % magnetic components, 0.13 % moisture, and 64.5 % of the size distribution spread over three consecutive sieves (150 – 600 μm). The sand was washed repeatedly to remove all the clay and oven dried. 2 kg washed sand samples were mulled with pre-determined weights of either catalyst to give 30 %, 50 % and 70 % by weight of 20 g Furotec 132 resin which was added last. Furotec 132 resin + Furocure CH Slow acid catalyst system gives longer bench lives and strip times but the maximum compressive strength in excess of 5000 N/cm2 is attained after more than 8.5 hours curing time irrespective of the weight % of catalyst added relative to the resin. On that basis, exceeding 30 weight % Furocure CH Slow acid catalyst when sand moulding with Furotec 132 resin has neither technical nor economic justification. In comparison, the Furotec 132 resin + Furocure CH Fast acid catalyst system was only capable of producing mould specimens with maximum compressive strength above 5000 N/cm2 at 30 weight % catalyst addition rate. At 50 and 70 weight % catalyst addition rates, the mulled sand rapidly turned dark green then bluish with a significant spike in temperature to about 40 oC, far exceeding the optimum curing temperature of Furotec 132. This high temperature accelerates the curing rate but with a very low degree of resin curing which explains the low compressive strength. In fact the sand grains fail to bond and have a dry, crumbly texture implying dehydration. Thus, not more than 30 weight % Furocure CH Fast acid catalyst should be used in sand moulding.
Influence exerted by various concentrations (0.01 to 50 ppm) of some chlorinated hydrocarbons (Aroclor 1254, Aroclor 1242, pp'DDE, pp'DDT and Lindane (ɣ НСН)) upon the photosynthetic assimilation of 14C02 in Antarctic marine diatom assemblage dominated by Corethron criophilum and some species of Nitzschia (Fragilariopsis group) has been investigated. The photosynthesis was fully inhibited by Lindane (ɣ HCH) in all applied concentrations To smaller extent the photosynthetic process was inhibited in turn by Aroclor 1242, pp'DDE and pp'DDT successively. Aroclor 1254 proved to be the least toxic. The possibility of the decrease of the primary production of the Antarctic diatoms caused by the chlorinated hydrocarbons was discussed.