In EU law a lot of attention has recently been paid to personal data protection standards. In parallel to the development of the general EU rules on data protection, the Members States also develop cooperation between law enforcement agencies and create new information exchange possibilities, including the processing of personal data of participants in criminal proceedings. The aim of this article is to analyse whether the personal data of victims of crime are safeguarded according to the standards of the Charter of Fundamental Rights. For this purpose, the author analyses two directives: 2012/29/EU, which regulates minimum standards of victims of crime; and 2016/680/EU (also known as the Law Enforcement Directive), which regulates personal data processing for the purpose of combating crime. Based on the example of the Polish legislation implementing both directives, the author comes to the conclusion that the EU legislation is not fully coherent and leaves too much margin of appreciation to the national legislator. This results in a failure to achieve the basic goals of both directives. The author expects the necessary reflection not only from the national legislator, but also from the European Commission, which should check the correctness of the implementation of the directives, as well as from national courts, which should use all possible measures to ensure that the national law is interpreted in the light of the objectives of the directives.

The ultrasonic flowmeter which is described in this paper, measures the transit of time of an ultrasonic pulse. This device consists of two ultrasonic transducers and a high resolution time interval measurement module. An ultrasonic transducer emits a characteristic wave packet (transmit mode). When the transducer is in receive mode, a characteristic wave packet is formed and it is connected to the time interval measurement module inputs. The time interval measurement module allows registration of transit time differences of a few pulses in the packet. In practice, during a single measuring cycle a few time-stamps are registered. Moreover, the measurement process is also synchronous and, by applying the statistics, the time interval measurement uncertainty improves even in a single measurement. In this article, besides a detailed discussion on the principle of operation of the ultrasonic flowmeter implemented in the FPGA structure, also the test results are presented and discussed

The designing process of high resolution time interval measurement systems creates many problems that need to be eliminated. The problems are: the latch error, the nonlinearity conversion, the different duty cycle coefficient of the clock signal, and the clock signal jitter. Factors listed above affect the result of measurement. The FPGA (Field Programmable Gate Array) structure also imposes some restrictions, especially when a tapped delay line is constructed. The article describes the high resolution time-to-digital converter, implemented in a FPGA structure, and the types of errors that appear there. The method of minimization and processing of data to reduce the influence of errors on the measurement is also described.

Three methods of estimating radii of spray droplets are discussed and results of their practical application in the case of explosively produced water spray are reported. Parameters of model radii distributions are fitted using the least squares method. Finally, the data obtained for a number of tests are used for estimating fraction of explosion energy used for pulverization of water in the process of explosive production of water-spray.

In this paper, the microstructure of laser beam welded Sc-modified AA2519-F has been taken under investigation. The welded joint has been produced using Fanuc 710i industrial robot equipped with YLS-6000 6 kW laser beam source. The welding speed and laser power were equal to 0.75 m/min and 3.2 kW, respectively. The investigation involved microstructure observations with the use of both light microscope and scanning electron microscope with energy dispersive spectroscopy (EDS) analysis of chemical composition and microhardness distribution measurements. It has been stated that laser beam welding allows to obtain Sc-modified AA2519-F weld of good quality, characterized by the presence of an equiaxed grain zone containing scandium-rich precipitates adjacent to the fusion boundary.

Industries that rely on additive manufacturing of metallic parts, especially biomedical companies, require material science-based knowledge of how process parameters and methods affect the properties of manufactured elements, but such phenomena are incompletely understood. In this study, we investigated the influence of selective laser melting (SLM) process parameters and additional heat treatment on mechanical properties. The research included structural analysis of residual stress, microstructure, and scleronomic hardness in low-depth measurements. Tensile tests with specimen deformation analysis using digital image correlation (DIC) were performed as well. Experiment results showed it was possible to observe the porosity growth mechanism and its influence on the material strength. Specimens manufactured with 20% lower energy density had almost half the elongation, which was directly connected with the porosity growth during energy density reduction. Hot isostatic pressing (HIP) treatment allowed for a significant reduction of porosity and helped achieve properties similar to specimens manufactured using different levels of energy density.