Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 244
items per page: 25 50 75
Sort by:
Download PDF Download RIS Download Bibtex

Abstract

In this paper, the analysis of carbon footprint values for children’s footwear was conducted. This group of products is characterized by similar small mass and diversity in the used materials. The carbon footprint is an environmental indicator, which is used to measure the total sets of greenhouse gas (GHG) emissions into the atmosphere caused by a product throughout its entire lifecycle. The complexity of carbon footprint calculation methodology is caused by multistage production process. The probability of emission greenhouse gases exists at each of these stages. Moreover, a large variety of footwear materials – both synthetic and natural, give the possibility of the emission of a lot of waste, sewage and gases, which can be dangerous to the environment. The diversity of materials could be the source of problems with the description of their origins, which make carbon footprint calculations difficult, especially in cases of complex supply chains. In this paper, with use of life cycle assessment, the carbon footprint was calculated for 4 children’s footwear types (one with an open upper and three with full uppers). The life cycles of the product were divided into 8 stages: raw materials extraction (stage 1), production of input materials (stage 2), footwear components manufacture (stage 3), footwear manufacture (stage 4), primary packaging manufacture (stage 5), footwear distribution to customers (stage 6), use phase (stage 7) and product’s end of life (stage 8). On these grounds, it was possible to point out the life cycle stages, where the optimization activities can be implemented in order to reduce greenhouse gases emissions. The obtained results showed that the most intensive corrective actions should be focused on the following stages: 3 (the higher emissivity), 4 and 8.

Go to article

Authors and Affiliations

Wioleta Serweta
Robert Gajewski
Piotr Olszewski
Alberto Zapatero
Katarzyna Ławińska
Download PDF Download RIS Download Bibtex

Abstract

The large variability and unpredictability of energy production from photovoltaic power microinstallations results from the dependence on the current weather conditions. These conditions depend on a number of factors and are variable over the time. Despite this specificity, photovoltaic micro-installations are becoming more and more popular in the world and in Poland. This is mainly due to the fact that the generation of energy from renewable sources has numerous advantages, the energy is free, renewable in time and ecological, and its production on its own gives partial independence from energy supplies from the power grid. In addition, the observed significant prices decrease of solar modules has further accelerated the development of the use of this energy source. Concern for this method of energy production among households has increased significantly in Poland after introducing the prosumer in the legal framework and the use of administrative and financial support. The implemented prosumer mechanisms allowed, for example, the net balancing of the energy consumed and produced by the micro-installation through storage in the power grid. The article describes the problem of balancing sources using solar energy, based on micro-installation used in the household (the so-called prosumer installation). The conducted analyses compared the load profile of a typical household and the energy generation profile from a photovoltaic installation, determining the real balancing formation level of such a system.

Go to article

Authors and Affiliations

Bartosz Soliński
Download PDF Download RIS Download Bibtex

Abstract

The article concerns issues related to need of the introduction of protection prognostic areas, prospective resources pursuant to the new regulations of integrated development and space management in Poland. The article discuss the issues of actual and crucial documents and it also contains some critic and detailed analysis of the documents such as: the Responsible Development Strategy (SOR), Integrated National Development Strategy (ZSRK), Poland Integrated Development Strategy (SZRP). Author also analyzes whether the level of the implementation with the provisions motioned above is compliant with work in the committees reviewing issues in accordance with the work of the inter-ministerial teams for the updating and monitoring the strategy of development, set up at the Coordination Committee for Development Policy. The article indicates, among others, the increase of the legislative risk for the geological-mining or energy industry, the commodity sector. The risk may affect the crucial matters for the industry (functional areas, ICPs, the basis of their recognition in planning documents – taken into consideration as an element in the integrated management system of development). After all the analysis of the current provision, the article contains the summary with the main conclusions.

Go to article

Authors and Affiliations

Jan Stefanowicz
Download PDF Download RIS Download Bibtex

Abstract

Mineral deposits are such type of assets, the valuation of which can be carried out in a very diverse manner. Methods and procedures for such a valuation are most often applied to mineral deposits with mineral reserves (according to the CRIRSCO classification), much less frequently and usually only using a comparative approach for undeveloped, initially recognized mineral deposits (with mineral resources).

In Poland, a significant portion of mineral deposits, mainly of energy, metal and chemical minerals, are covered by the so-called mining property of the Treasury. At the moment, there is a lack of consistent and thoughtful management of these deposits. The appropriate methodology for valuing these deposits, which are at various stages of recognition (sometimes also of development), should be one of the key elements of such management. The State Treasury usually disposes of mining rights by “establishing” mining usufruct in the form of a contract, with the determination of remuneration for this establishment. The rules for determining remuneration for the establishment of mining usufruct are determined on the basis of an internal informal document of the Ministry of the Environment with very simplified rules for determining this remuneration, to a very limited extent related to the actual value of the deposit, which is also variable over time. This fee should be in close relation to the value of the mineral deposit valued at a given moment, taking the current conditions, including technological, environmental, formal and legal, and – in particular – market conditions into account. The valuation of mineral deposits covered by mining property, except for current needs in determining the basis for remuneration for mining usufruct establishing, should also be used to determine the value of these deposits annually as part of the State Treasury property and to present its results as part of the State Treasury Property Status Report.

It is an open matter whether the methodology of valuation of the discussed mineral deposits should be based on accepted and widely used solutions for the valuation of mineral deposits for the purposes of business transactions or based on methodology of valuation of deposits as part of the planned system of Integrated Environmental and Economic National Account (up to date poorly developed). The paper presents the most important elements of both methodological approaches. It seems that the use of selected elements of each of these approaches would be advisable in this case.

Go to article

Authors and Affiliations

Krzysztof Galos
Download PDF Download RIS Download Bibtex

Abstract

The operational mineral deposit reconnaissance tends to evaluate its parameters to conduct safe and profitable production. Particular deposit parameters, important from the point of mineral deposit management, are estimated on the basis of observations carried out by mining geological surveys. These observations usually involve sampling, drilling, laboratory analyses and others. The use of fuzzy description to assess the parameters of the mineral deposit was proposed in the paper. In the fuzzy characteristics, an imprecise descriptive description appeared in place of a particular numerical quantity. This approach was used to description of the ore deposit features (metal content, volume, and metal yield) by assigning them specific characteristic functions, whose distributions were based on basic statistical quantities. Characteristic functions can be used to prepare operational strategies for any configuration of required deposit parameters resulting from the production management needs. For this purpose, selected logical operators of fuzzy sets were used. In the next approach to fuzzy modeling, an opportunity to characterize the deposit in a subjective approach was indicated, where the assessment of the deposit parameters is based on rough, in some way, discretionary observation and evaluation. Such model construction enabled the overall assessment of the deposit from the point of view of any parameters. Through the implementation of appropriate inference rules, adequate fuzzy control planes were obtained, which may also be useful in the context of operational mine strategy planning.

Go to article

Authors and Affiliations

Mariusz Krzak
Paweł Panajew
Download PDF Download RIS Download Bibtex

Abstract

The aim of this article is to present the author’s opinion about possible underwater natural gas pipeline monitoring using Polish Navy resources. Due to the bathymetrical characteristics of the pipeline equatorials the high efficiency and safe for the deck operators systems are expected to support the bottom survey and gas line monitoring. Time and engaged resources reduction are crucial factors in this kind of mission together with high probability of possible dangerous objects detection. The paper describes main threats for the underwater transportation line as a state energetic independence vital object (supplies diversification). An example of a threat caused by lost unmanned platform technologies near Nord Stream was presented and analyzed as well. The rapid development of unmanned maritime technologies (aerial, surface and subsurface) observed in the last decade creates new possibilities in maritime security/surveillance applications. The Polish mine counter measures assets which were equipped with sophisticated AUV’s as a part of the Polish Navy modernization process (new minehunters Kormoran IInd class deployable). The presented autonomous underwater vehicles (AUV) are equipped with advanced sonars and create new possibilities in the issue of effective threats detection/classification/ identification and neutralization. The main advantages of such solutions were pointed in the article with the crucial one based on time reduction as well as human – deck operators threats constraints. The first successes in the operational use of unmanned systems were reached during the military exercises (historical ordnance disposal) conducted on historical mine laying areas. This creates good possibilities to train the unmanned system operators in live objects activity which improves skills and knowledge. Moreover, the double use applications of unmanned technologies both in defense and maritime security has been observed.

Go to article

Authors and Affiliations

Rafał Miętkiewicz
Download PDF Download RIS Download Bibtex

Abstract

This publication presents an assessment of the economic efficiency of a hypothetical installation for the gasification of the municipal and industrial waste for the production of syngas used subsequently for the production of energy or chemical products. The first part of the work presents an example of a technological system for the energo-chemical processing of coal mud and municipal waste, based on the gasification process using a fluidized bed reactor. A hypothetical installation consists of two main blocks: a fuel preparation unit and a gasification unit. In the fuel preparation installation, reception operations take place, storage, and then grinding, mixing, drying and transporting fuel to the gasification unit. In the gasification installation, fuel gasification, oxygen production, cooling and purification of raw process gas and ash treatment are carried out. The following key assumptions regarding the gasification process, as well as the capital expenditures and operating costs related to the process, were estimated. Consequently, based on the method of discounted cash flows, the unit cost of generating energy contained in the synthesis gas (cost of energy, COE) was determined and the results were interpreted. In order to obtain an acceptable efficiency of the gasification process for waste fuels for the production of alternative fuel (process gas), it is necessary to supplement the mixture of waste coal and coal mud with the RDF. In this case, the unit cost of fuel measured by the PLN/GJ index is lower than in the case of hard coal and comparable with brown coal. The use of coal mud for the production of process gas in an economically efficient way is possible only in the case of changes in the legal system allowing for charging fees for the utilization of industrial waste – coal mud.

Go to article

Authors and Affiliations

Krzysztof Kwaśniewski
Paweł Grzesiak
Radosław Kapłan
Download PDF Download RIS Download Bibtex

Abstract

Recently, the search for new effective energy production solutions has been focused on the production of electricity using renewable and environmentally friendly carriers. This resulted in an increased interest in PV cells and cogeneration systems. The article looks at the main factors affecting their operational parameters against the background of the development history of subsequent generations of PV cells. Average daily solar radiation and wind velocity in Lodz were characterized. The research was done on a static and tracking system with a total peak power of 15 kWp and a 30 kW microturbine. PV panels are installed on the building of the Institute of Electrical Power Engineering of the Lodz University of Technology and they work as part of DERLab. A microturbine is inside the building. Energy measurements were carried out in 2016 giving grounds for the analysis of energy efficiency and financial analysis of the energy supply in buildings. Energy yields in the static and tracking system as well as percentage coverage of electricity from PV cells and microturbines were assessed. The distribution of monthly savings, annual savings of energy costs and the payback time of the investment costs of the systems subject to the test were determined. The research we have done allows us to say that the energy produced by follow-up modules is about 3 times greater than that generated in stationary modules. On the other hand, the annual savings of energy costs using gas micro-turbines are about 10 times higher than those of lagging panels. The analysis shows that it is possible to determine the profitability of the microturbine and photovoltaic panels use despite large financial outlays. The payback period of investment outlays is about 12 years when using the installation throughout the year.

Go to article

Authors and Affiliations

Paulina Sawicka-Chudy
Elżbieta Rybak-Wilusz
Maciej Sibiński
Marian Cholewa
Ryszard Pawełek
Download PDF Download RIS Download Bibtex

Abstract

Fractal analysis is one of the rapidly evolving branches of mathematics and finds its application in different analyses such as pore space description. It constitutes a new approach to the issue of their natural irregularity and roughness. To be properly applied, it should be encompassed by an error estimation. The article presents and verifies uncertainties along with imperfections connected with image analysis and expands on the possible ways of their correction. One of key aspects of such research is finding both appropriate place and the number of photos to take. A coarse- grained sandstone thin section was photographed and then pictures were combined into one, bigger image. Fractal parameters distributions show their change and suggest that the accurately gathered group of photos include both highly and less porous regions. Their amount should be representative and adequate to the sample. The resolution influence on the fractal dimension and lacunarity values was examined. For SEM limestone images obtained using backscattered electrons, magnification in the range of 120x to 2000x was used. Additionally, a single pore was examined. The acquired results point to the fact that the values of fractal dimension are similar to a wide range of magnifications, while lacunarity changes each time. This is connected with changing homogeneity of the image. The article also undertakes a problem of determining fractal parameters spatial distribution based on binarization. The available methods assume that it is carried out after or before the image division into rectangles to create fractal dimension and lacunarity values for interpolation. An individual binarization, although time consuming, provides better results that resemble reality to a closer degree. It is not possible to define a single, correct methodology of error elimination. A set of hints has been presented that can improve results of further image analysis of pore space.

Go to article

Authors and Affiliations

Michał Figiel
Download PDF Download RIS Download Bibtex

Abstract

The paper presents the characteristics of the attitude that students have towards electric cars and the significance of distinguished attitude elements in creating interest in the purchase of such vehicles. Electric cars are the new type of vehicles that have an electric motor and use the electricity stored in batteries. They are introduced to the market, but for various reasons the volume of sales is not high. So far, it is not sufficiently known how electric vehicles are assessed by Poles. The presented research is an attempt to know what the attitude towards this type of vehicle. The attitude model tested in this research includes three areas: knowledge about them, emotions that they evoke and potential behaviors. The participants were students of Rzeszów University of Technology – a group of young people who are potential consumers of new technologies. The obtained results indicate that electric cars are rather unknown. At the same time, they arouse great interest and their image is very positive. The attitude characteristics towards this type of vehicle is supplemented by perceived limitations: too high of a purchase price, lack of sufficient information about them and unsatisfactory technical parameters, mainly the long time needed to recharge the battery and the insufficiently long distance with one recharge. The interest in the purchase is dependent on positive emotions, and the lack of sufficient information is an obstacle in thinking about buying such a vehicle. Understanding the attitudes of Polish students towards electric cars can be helpful in adapting information about such cars to potential customers, which in turn may affect the level of interest and sales volume.

Go to article

Authors and Affiliations

Ryszard Klamut
Download PDF Download RIS Download Bibtex

Abstract

The Polish energy sector is, to a large extent, based on fossil fuels used in conventional energy, which is not entirely consistent with the current energy policy of the European Union. Therefore, it is necessary to increase the use of renewable energy sources that guarantee the preservation of the value of the natural environment in rural areas. It should be emphasized that in addition to the economic effect, the environmental effect is very important, understood as the impact of renewable energy on the natural environment and the quality of life of rural residents. The intensive development of RES raises a lot of controversy among politicians, as well as among rural residents, who are also associated with the myths regarding renewable energy as harmful to the natural environment.

Rural development should be connected with the socio-economic situation, and even more so with the socio-cultural situation of its inhabitants, because it assumes that the development of rural areas in Poland is associated not only with agriculture, but also with historical and natural values and their durability.

The aim of this work is to determine the attitudes of the inhabitants of rural areas of the Podkarpackie Province on the impact of renewable energy sources on the natural environment. The work assumes that the durability of rural areas is largely connected with the ability to preserve their natural values, as well as ensuring a satisfactory quality of life for residents. The basic source of data was surveys carried out in 2017 among 282 inhabitants of the Podkarpackie Province .

Go to article

Authors and Affiliations

Marian Woźniak
Bartosz Saj
Download PDF Download RIS Download Bibtex

Abstract

The development of electromobility is a challenge for the power system in both technical and economic-market terms. As of today, there are no analyses to determine the power necessary to supply the planned infrastructure and to estimate the incentives and economic benefits resulting from the modification of the settlement method. The document determining the legal regulations and the obligation to build vehicle charging stations for specific municipalities is the Act on Electromobility and Alternative Fuels. This act estimates that the development of electromobility, due to the specifics including not only individual vehicles, will take place in certain areas. The places which in the first stage will be dedicated to the potential implementation of the concept of electromobility will be municipalities covering large agglomerations. In addition, due to the local aspect, the development of electromobility may take place in the areas of energy clusters’ initiatives, which, using the policy of increasing energy awareness, are aimed at energy production from local renewable energy resources. The planned development of electromobility assumes a systematic increase in the number of electric cars caused by the introduction of support systems. The dynamization of this sector will cause an increase in the demand for electricity. Due to power system reasons, an important factor determining the level of energy consumption depending on the time of day may be an appropriate shape of the pricing for the charging service. Appropriate price list stimulation can affect the behavior of recipients, causing the charging of cars in the off-peak of electricity demand. The aim of the article is to characterize the scale of the phenomenon of electromobility in the context of the emergence of a charging points infrastructure along with the possibility of price-setting stimulation affecting the profile of energy demand. It is also important to consider the challenges and responsibilities of municipalities and energy clusters from the perspective of introducing electromobility.

Go to article

Authors and Affiliations

Kinga Bojda
Maciej Sołtysik
Download PDF Download RIS Download Bibtex

Abstract

The energy efficiency of photovoltaic modules is one of the most important aspects in energetic and economic aspects of the project related to system installations. The efficiency of modules and the electricity produced by photovoltaic conversion in solar modules is affected by many factors, both internal, related to the module structure itself and its technical and external factors related to the energy infrastructure, which includes: cabling, inverters, climate conditions prevailing at the micro-installation location and the orientation and angle of inclination of the solar modules. The installation of photovoltaic modules should be preceded by an energy efficiency analysis, which will help to indicate the optimal solution adapted to the given conditions. The article presents a comparative analysis of the amount of energy produced under real and simulated conditions. Analyzes were made on the basis of research carried out in the Wind and Solar Energy Laboratory located at the AGH University of Science and Technology, data from solar irradiation data-bases and computer software for estimating energy resources. The study examined the correlation of the solar irradiation on the modules and the amount of electricity generated in the photovoltaic module. The electricity produced by the module was compared under real conditions and simulated based on two sources of data. The comparison and analysis of the amount of energy of the module were also made, taking simulated different angles of the module’s inclination into account.

Go to article

Authors and Affiliations

Bartosz Soliński
Monika Stopa
Download PDF Download RIS Download Bibtex

Abstract

Due to unfavorable factors, dangerous conditions occurred in the delivery of electric energy in Poland. This was the most serious incident of its kind since the 1980’s. Such a serious incident raised concern about the safety of the electric power system in the summer and led to the formulation of conclusions for the future. In this article, the author analyses the conditions, which caused that situation. Poland was experiencing a doubt in August 2015, which along with an extremely high maximum daily temperature created remarkably unfavorable conditions for power plants and decreased the capacity of overhead power lines. Such unfavorable metrological conditions occurred not only in Poland, but also in Central-Eastern and Western Europe. It is worth emphasizing that the safety of electric energy delivery was endangered only in Poland. The improper renovation and upkeep policies, as well as unplanned outages in power plants caused a significant decrease of available power in the National Electric Power System. Unscheduled flows between Germany and Poland ruled out the possibility of importing electric energy at such a critical time. The author presents the correlation between the maximum daily air temperature in the sweltering heat and an increase in the demand for electric energy. Overall, unfavorable conditions posed a threat in the delivery of electric energy in Poland. In this article, the author draws attention to the report from the Supreme Audit Office (Najwyższa Izba Kontroli – NIK) from 2014, which predicted such a dangerous situation. Unfortunately, that report remained unnoticed. The author formulated appropriate solutions in order to increase the safety of electric energy delivery in the summer and to prevent such occurrences in the future.

Go to article

Authors and Affiliations

Bartosz Sobik
Download PDF Download RIS Download Bibtex

Abstract

The implementation of micro scale combined heat and power systems is one of the ways to improve the energy security of consumers. In fact, there are many available large and medium scale cogeneration units, which operate according to the Rankine Cycle. Due to European Union demands in the field of using renewable energy sources and increasing energy efficiency result in the importance of additionally developing systems dedicated for use in residential buildings, farms, schools and other facilities. This paper shows the concept of introducing thermoelectric generators into typical wood stoves: steel plate wood stoves and accumulative wood stoves. Electricity generated in thermoelectric generators (there were studies on both three market available units and a prototypical unit developed by the authors) may be firstly consumed by the system (to power controller, actuators, fans, pumps, etc.). Additional power (if available) may be stored in batteries and then used to power home appliances (light, small electronics and others). It should be noted that commercially available thermoelectric generators are not matched for domestic heating devices – the main problems are connected with an insufficient heat flux transmitted from the stove to the hot side of the generator (caused e.g. by the non -homogeneous temperature distribution of the surface and bad contact between the stove and the generator) and inefficient cooling. To ensure the high efficiency of micro cogeneration systems, developing a dedicated construction both of the generator and the heat source is necessary.

Go to article

Authors and Affiliations

Krzysztof Sornek
Mariusz Filipowicz
Download PDF Download RIS Download Bibtex

Abstract

From all the detonation parameters of explosives, “strength” – the capability to perform work is the most important for the user. The detonation of explosives in the blast hole is a quick and complicated process: first there is a detonation pressure causing the crushing of the rock in the vicinity of the explosive, then the pressure of the detonation products causes the cracking of the rock. The article presents the methods of determining the capability to perform work by explosives for civil use (dynamite and ANFO) used in the accredited Laboratory of Explosives and Electric Detonators Testing of the Experimental Mine “Barbara” of the Central Mining Institute – the lead block (Trauzl) method and the ballistic pendulum method. The aim of the research was to determine the relationship between the values of the capability to perform the work received in a ballistic pendulum method and a lead block method. As a result of the performed tests and the analysis of the results, the α-Pb coefficient was determined, which can be used to convert the value of the capability to perform work on the ballistic pendulum to the corresponding value of the capability to perform work in the lead block. At present, the Central Mining Institute is the only Notified Body of the European Union in the scope of Directive 2014/28 /EU, which has a station for smelting lead blocks and equipment and for determining the capability to perform work by explosives in lead blocks – this method was abandoned in other research units for testing with a ballistic pendulum and/or underwater test.

Go to article

Authors and Affiliations

Michał Szastok
Download PDF Download RIS Download Bibtex

Abstract

Describing the gas boiler fuel consumption as a time series gives the opportunity to use tools appropriate for the processing of such data to analyze this phenomenon. One of them are ARIMA models. The article proposes this type of model to be used for predicting monthly gas consumption in a boiler room working for heating and hot water preparation. The boiler supplies heat to a group of residential buildings. Based on the collected data, three specific models were selected for which the forecast accuracy was assessed. Calculations and analyses were carried out in the R environment using “forecast” and “ggplot2” packages. A good quality of the obtained forecasts has been demonstrated, confirming the usefulness of the proposed analytical tools. The article summary also indicates for what purposes the forecasts obtained in this way can be used. They can be useful for diagnosing the correct operation of a heat source. Registering fuel consumption at a level significantly deviating from the forecast should be a signal to immediately diagnose the boiler room and the heat supply system and to explain the reason for this difference. In this way, it is possible to detect irregularities in the operation of the heat supply system before they are detected by traditional methods. The gas consumption forecast is also useful for optimizing the financial management of the property manager responsible for the operation of the boiler room. On this basis, operating fees or financial operations with the use of periodic surplus capital may be planned.

Go to article

Authors and Affiliations

Grzegorz Bartnicki
Bogdan Nowak
Download PDF Download RIS Download Bibtex

Abstract

Economic development is strictly dependent on access to inexpensive and reliable energy sources based on diversified primary fuels. The strategic framework for the construction of the energy mix is defined in the Energy Policy of the State, the content of which, in terms of its mandatory elements, has been specified in the Energy Law. The task of the Energy Policy of the State is to create the shape of the future power sector, including designing the most advantageous regulatory, system and technical solutions guaranteeing the appropriate level of energy security of the country, monitoring of the system’s evolution and also designing and implementing changes aimed at the optimization of the functioning mechanisms. The vision of the development of the power system at the global level should also reflect changes in the formation of dispersed civil energy structures. Unfortunately, the results of the conducted analyses reveal existing imperfections of the data acquisition and information system, which should be used in the planning process. This issue is particularly important from the perspective of the dynamically developing concept of the energy self-sufficiency of communes and the emergence of energy clusters. The present paper describes the functioning of strategic planning in the field of the electric power system with an illustration of the improperly functioning mechanisms of information transfer in the context of the advancement of dispersed civil energy structures.

Go to article

Authors and Affiliations

Maciej Sołtysik
Sylwia Całus
Marcin Malec
Download PDF Download RIS Download Bibtex

Abstract

The efficient protection (support reinforcement) of a wall and heading crossing ensures continuity of the production cycle, and that is a quick moving of the scraper conveyor to the wall. Using low or high bolting as a support reinforcement element in wall and heading crossings allows for the elimination of traditional methods of maintaining longwall-gate crossings, and therefore allows for the efficient use high performance modern wall complexes. The paper presents the long underground experience, of the Knurów–Szczygłowice mine of efficient support wall and heading crossing maintenance, which was bolted to the rock mass with the usage of two pairs of bolts, showing full technical and economical usefulness of this support reinforcement method. The article also highlights work safety and the increasingly common usage of endoscopies when specifying the range of crack areas which directly effects the proper choice in number, load-capacity and length of the used bolts. The underground studies the measurements of the reach of the zones of fracturing and roof stratification (using endoscopes and wire type stratification meters) and the laboratory tests (using the test stand) have allowed to determine the safety factor for maintenance of the longwall gangway crossing, directly resulting in the necessity to install additional reinforcement. The value of the safety factor Sbsc-ch greater than 1 is advantageous and safe, and the value less than or equal to 1 can lead to a significant deterioration of the conditions of maintenance of a wall and heading crossing which was bolted.

Go to article

Authors and Affiliations

Stanisław Duży
Piotr Głuch
Grzegorz Michalik
Adam Ratajczak
Download PDF Download RIS Download Bibtex

Abstract

Having increasingly tightened geological and mining conditions in which the extraction of copper ore deposits in Poland is conducted, ensuring effective and safe mining is presently becoming a key task and a significant challenge for mine operators, mainly in the field of ground support systems being the equivalent for the new geological/mining conditions. As one may expect, these conditions shall be characterized by higher values of the primary stress tensor elements as well as the lower deformability and higher strength of the rock mass surrounding the copper ore body. T his means that in the near future, the rock bursts problem will become one of the most important issues deciding on the economy and safety within the newly developed mining areas. T herefore developing a novel effective ductile ground support systems which could be able to control the rock mass movement in squeezing and burst-prone rock conditions is recommended. T his type of requirement may fulfil only ductile or, in other words, the kinetic energy-absorbing systems, which permit slowing down a movement of violently ejected rock blocks. T his paper’s objective is to present the idea of the development of a new type of an effective and low cost ductile resin anchored rockbolt system with smooth and of the square cross-section steel rod is formed in coil shape of different pitch. T he developed bolt prototypes have been tested underground in the G-11 section of the Rudna mine. Results of the pull-out tests, involving different bolts’ shapes and different sliding materials set on the rockbolts’ rods, have proved those bolts’ efficiency as an element of the ductile support system.

Go to article

Authors and Affiliations

Witold Pytel
Piotr Mertuszka
Krzysztof Szeptun
Download PDF Download RIS Download Bibtex

Abstract

Methane explosions are among the greatest hazards in the Polish coal mining industry and unfortunately continue to cause many catastrophes. The constant growth of the depth of coal exploitation in the conditions of the high concentration of mining causes the increase of absolute methane content and methane seam pressure from the mined seams. This situation directly affects the increase in the level of methane hazard in the underground work environment. It is therefore obvious to undertake intensive research that will allow for the development of appropriate solutions that help to exclude the risk of mining catastrophes resulting from the ignition and/or methane explosion. In addition to the development of methane hazard prevention methods, an indispensable element of this approach is a very accurate identification of the mechanisms of the combustion and explosion of this gas. The article presents the method of investigation and examples of results of methane explosions carried out in the 400 m experimental gallery of the Experimental Mine “Barbara” of the Central Mining Institute – the only large scale underground experimental facility in Europe. A n analysis has been performed of the influence of the methane release into mining workings on the distribution of the gas concentration and on the course of its explosion or combustion. The data collected characterizes thermodynamic phenomena that form the basis for determining the level of the explosion hazard. Large scale studies have also allowed to assess the risk of conditions that are sufficient for the development of a coal dust explosion initiated by methane explosions. The large scale of the experiments and the system of continuous recording of the course of the experiments allowed the specific characteristics of the methane explosion and burning in underground mining workings to be identified and isolated. For the first time, the course of experiments was recorded via a camera system deployed along the gallery.

Go to article

Authors and Affiliations

Krzysztof Cybulski
Zdzisław Dyduch
Robert Hildebrandt
Henryk Koptoń
Download PDF Download RIS Download Bibtex

Abstract

The contemporary underground mining of raw minerals is more and more associated with geological and mining software packages which support the work of designers from the moment of the exploration of a deposit, determination of its size and quality, geological, hydrogeological and tectonic conditions, by planning the development and cutting of the deposit. Production planning is one of the most important activities carried out in the course of a mining project, because it allows to set specific production results of a mine in relation to a time unit, and then allows for a verification of the degree of completion of the assumed plan. At present, computer-aided design is applicable to daily or long-term output planning taking deposit, qualitative, quantitative and cost constraints into account. In the article, selected forms of ore deposits were presented. On the basis of several dozen boreholes up to 300m in length, an exemplary fragment of the ore cutting model using computer-aided design of mining works was presented. By using modern computer software - ABB MineScape with modular construction, the possibilities of improving the process of development of future exploitation areas have been determined. In particular, the arrangement of boreholes, based on which ones the cross sections were made with, present the exemplary lithostratigraphic thickness of layers, including the location of discontinuous deformations in the form of faults, and an ore bearing zone. For the block model, resources with priority for metal N o. 1 and 2 were calculated. I n the last section of the article, the cutting idea for a shallow ore deposit has been presented. The degree of effective use of the deposit has been analysed for the room and pillar mining method.

Go to article

Authors and Affiliations

Krzysztof Skrzypkowski
Waldemar Korzeniowski
Andrzej Gądek
Radosław Misiak
Download PDF Download RIS Download Bibtex

Abstract

The assessment of a rock’s behaviour around excavations and the effectiveness of its reinforcement in underground ore mines is dependent on the performance of the rock-bolt and rock-mass interaction, which can be estimated on the basis of appropriately designed measurements. Based on the background of various measurements solutions described in the literature, concerning rock bolt monitoring methods, the authors proposed a new, original device for mass measurements in mine conditions. After examining the advantages and disadvantages of existing constructions, the article presents the essence, principle of operation and method of measuring anchor load in an underground excavation with the a instrument, indicator WK-2/8. The prototype has been carefully researched and successfully tested in a full-scale laboratory environment. This instrument, also referred to as a load indicator or force pad, does not require electrical power and allows for relatively accurate (with a resolution of 10-14kN, up to about 90kN loading capacity) and a remote reading of the axle loading of the anchor (AGH patent) by any person present in the specified area. The device can be installed in mining excavations under loading conditions. The relatively low cost of a measuring instrument, practically used as an additional washer, as well as an easy assembly method, makes it universally applicable in mines where anchoring is used as a means of strengthening the rock.

Go to article

Authors and Affiliations

Waldemar Korzeniowski
Krzysztof Skrzypkowski
Łukasz Herezy
Download PDF Download RIS Download Bibtex

Abstract

The paper presents differences between technical states and technical operation states of haul trucks in the technical operation process. The specification and analysis of operational parameters of technological vehicles used in surface mining is possible only due to more and more frequently used diagnostic – telemetric systems. While a detailed analysis of machines operation data can result in the more effective management of mining plant operations and the mining process itself. The determination of operational state indices and their individual components allows preventive actions to be commenced, resulting in improving the work organization of the entire mine machinery system. Moreover, the future technical state of machines operated in surface mining is strictly related to the current state and also depends on the events that occurred in the extraction system. A set of parameter values of individual state characteristics, which allow the haul trucks technical and operational state to be characterized, is a direct effect of a telemetric – diagnostic system operation.

Go to article

Authors and Affiliations

Przemysław Bodziony
Michał Patyk
Zbigniew Kasztelewicz

This page uses 'cookies'. Learn more