Bragg scattering of waves propagating in a periodically disturbed substrate is widely applied in optics and micro-acoustic systems. Here, it is studied for Rayleigh waves propagating on a periodically grooved elastic substrate. Practically applied groove depth in the Bragg grating reflectors does not exceed a few percent of the Rayleigh wavelength. Here, the analysis is carried out for periodic grooves of larger depth by applying the elastic plate model for the groove walls. The computed results show that the surface wave existence and reflection depends strongly on both the groove depth and period, and that there are limited domains of both for practical applications, primarily in comb transducers of surface waves.
In this paper a possibility of determining a local velocity of the surface acoustic Rayleigh waves using a transducer, with the rigidly connected emitting and receiving parts, is considered. A problem on spatial resolution of such a transducer for investigation of inhomogeneous specimens is also examined. A high spatial resolution can be obtained due to the transducer displacement by a value less than the distance between the emitting and receiving parts. It is shown that in this case it is not necessary to measure the transducer displacement with a high accuracy for precise determination of the velocity. Such an effect is obtained through measuring the velocity of surface waves in one local region of the specimen with respect to the other. The criterion for optimal spatial resolution selection during spatially inhomogeneous specimens study is also proposed. The proposed criterion use is illustrated on the example of the determination of spatial distribution of the surface acoustic velocity in a steel specimen subjected to inhomogeneous plastic deformation.
The paper presents a measuring system based on two resonators with a SAWacoustic surface wave. One of the resonators contains a sensor structure consisting of a Nafion layer with a PANI polyaniline nanolayer deposited on it. The sensor structure was tested for carbon monoxide, with a very low concentration (5, 10, 15, 20 ppm) in the atmosphere of synthetic air. The structure sensitivity was tested for two different PANI thicknesses: (100 and 180 nm). The tests were carried out for two different temperatures: 308 K and 315 K. The investigations shows that the measuring system used with the acoustic surface wave together with the proposed sensing layers is sensitive to the presence of low concentration carbon monoxide molecules in the atmosphere of synthetic air.
Parameters of surface acoustic waves (SAW) are very sensible to change of physical conditions of a propagation medium. In the classical theory formulation, the waves are guided along the boundary of semi-infinity solid state and free space. A real situation is more complex and a medium commonly consists of two physical components: a solid substrate and a gaseous or liquid environment. In the case of stress-free substrate, the strongest impact on SAW properties have surface electrical and mechanical conditions determined by solids or liquids adhering to the boundary. This impact is utilised for constructing sensors for different gases and vapours e.g. (Jakubik et al., 2007; Hejczyk et al., 2011; Jasek et al., 2012). The influence of gaseous environment on the SAW properties is usually very weak and ignored. However, in certain condition it can be significant enough to be applied to sensor construction. In general, it concerns Rayleigh wave devices where energy leakage phenomenon is perceptible, especially when the gas being detected considerably changes the density of environment. The paper presents the results of experiments with oxygen-nitrogen mixture. Their primary aim was focused on finding the dependence of resonant frequency and attenuation in SAW resonator on parameters and concentrations of the gas in the environment.
The aim of this publication is to design a procedure for the synthesis of an IDT (interdigital transducer) with diluted electrodes. The paper deals with the surface acoustic waves (SAW) and the theory of synthesis of the asymmetrical delay line with the interdigital transducer with diluted electrodes. The authors developed a theory, design, and implementation of the proposed design. They also measured signals. The authors analysed acoustoelectronic components with SAW: PLF 13, PLR 40, delay line with PAV 44 PLO. The presented applications have a potential practical use.
Modern gas turbine systems operate in temperatures ranging from 1200°C to even 1500°C, which creates bigger problems related to the blade material thermal strength. In order to ensure appropriate protection of the turbine blades, a sophisticated cooling system is used. Current emphasis is placed on the application of non-stationary flow effects to improve cooling conditions, e.g., the unsteady-jet heat transfer or the heat transfer enhancement using high-amplitude oscillatory motion. The presented research follows a similar direction.
A new concept is proposed of intensification of the heat transfer in the cooling channels with the use of an acoustic wave generator. The acoustic wave is generated by an appropriately shaped fixed cavity or group of cavities. The phenomenon is related to the coupling mechanism between the vortex shedding generated at the leading edge and the acoustic waves generated within the cavity area. Strong instabilities can be observed within a certain range of the free flow velocities.
The presented study includes determination of the relationship between the amplitude of acoustic oscillations and the cooling conditions within the cavity. Different geometries of the acoustic generator are investigated. Calculations are also performed for variable flow conditions. The research presented in this paper is based on a numerical model prepared using the Ansys CFX-17.0 commercial CFD code.