One of the main threats to constructions made from rammed earth is destruction due to exposure to water. The way to limit this dangerous phenomenon is to supplement the local soil mixtures with stabilizing agents. The main component used is Portland cement. This article analyses the results of research which focused on the resistance of rammed earth to water erosion. Because of the lack of national standards regarding the method of examining the durability of rammed earth, the research was based on the New Zealand standard NZS 4298: 1998. The results confirm the possibility of using rammed earth stabilized by cement in a temperate climate.
Forest stand decomposition of the Silesian Beskids which is followed by the tree cutting has been observed since the beginning of the 21st century. Changes in forest management due to the introduction of heavy machines for forest work mainly for skidding have been observed in the Silesian Beskids for the last decade. The paper presents results of a three-year investigation of erosion gullies forming in mountain forest after the skidding performed with use of heavy equipment. In the Wilczy Potok catchment comprising an area of above 100 ha 40 gullies were identified. The measurement of the length and depth of gullies showed that the total volume of soil and rock material removed from the catchment area due to erosion accelerated by skidding exceeded 9 000 m3. The year erosion rate for deep gullies was found to be 10%. The presented results show that necessary protective actions and preventive measures should be taken to mitigate the soil degradation processes.
The study on water erosion in the catchment basin of the Jeleni Brook was carried out in the years 1995–1999. The catchment of the Jeleni Brook has complex relief, receives frequent pre-cipitations and thus is more threatened by water erosion. Soil cultivation and water from quickly melting snow can also be the factors affecting soil erosion. Waters from the melting snow produce rills of the following dimensions (mean values): width from 11.5 to 13.6 cm, depth – from 6.4 to 7.1 cm and length – from 39 to 112 m. The mean values of soil losses vary from 0.5 to 2.02 t·ha–1.
Erosion caused by intensive storm precipitation occurs less frequently but makes much higher soil losses. One of the registered incidents shows that 51.6 t·ha–1 (4.5 mm of soil layer) can be washed out from the area of 0.66 ha. Combined effect of outwashing and ploughing in lower parts of slopes created new forms of relief such as agricultural terraces (escarps). Agricultural terraces assume the shape of scarps up to 2 m high and of different length (e.g. 150 m) along with the land use border-lines between e.g. forest and field or field and grassland.
Agriculturally used soils within this catchment need protection based mainly on agrotechnical measures or on alteration of land use. Some areas should be afforested.
A sediment trap with bamboo materials can be utilized as one alternative of eco-friendly technology to reduce the ero-sion that occurred on agricultural land. This study aims to determine the most efficient form of that sediment trap in the field. Location study is in the Tulungrejo Village, Batu, Indonesia, which has andosol soil type and 35 cases of a landslide in 2013. Three forms of sediment traps were used (square, trapezoidal, and stratified type) with the purpose to find the most effective form. It is obtained that the most effective sediment trap is a stratified form with the 31.91% effectiveness or able to withstand sediment of 25.02 kg, while the adequate number is two pieces with the ability to withstand the most consider-able sediment of (91.70%). Therefore this stratified form of sediment traps is effective in erosion prevention on agriculturalland in the study area. For further development, it is required to test out the variations of the contents in a broader area with a more varied level of the slope.
The paper presents the results of the pitting resistance investigations of selected stainless steels in the chloride environment and the simultaneous impact of erosive factors using the cyclic polarization technique. Additionally, using electrochemical techniques, ie: electrochemical impedance spectroscopy (EIS) and measurement of corrosion potential, the behavior of the passive layer of selected stainless steels in the environment of chlorides and erosion was examined. On the basis of the obtained results, the resistance of stainless steels 1.4301 and 1.4404 was found, both on the effect of chloride ions and erosive factors in the studied systems. Both tested steels are susceptible to pitting corrosion. It was found that a good measure of erosive impact on stainless steel is both impedance spectrum analysis and continuous monitoring of the corrosion potential of steel.
The article presents research on solid particle erosive wear resistance of ductile cast iron after laser surface melting. This surface treatment technology enables improvement of wear resistance of ductile cast iron surface. For the test ductile cast iron EN GJS-350-22 surface was processed by high power diode laser HPDL Rofin Sinar DL020. For the research single pass and multi pass laser melted surface layers were made. The macrostructure and microstructure of multi pass surface layers were analysed. The Vickers microhardness tests were proceeded for single pass and multi pass surface layers. The solid particle erosive test according to standard ASTM G76 – 04 with 30°, 60° and 90° impact angle was made for each multi pass surface layer. As a reference material in erosive test, base material EN GJS-350-22 was used. After the erosive test, worn surfaces observations were carried out on the Scanning Electron Microscope. Laser surface melting process of tested ductile cast iron resulted in maximum 3.7 times hardness increase caused by microstructure change. This caused the increase of erosive resistance in comparison to the base material.
Water reaches a river in the form of surface runoff (precipitation that has not seeped into the ground) or underground outflow (groundwater). Both of these factors affect the erosion and river deposition processes that shape the river valley. Understanding them is crucial for effective river management.
To improve bioremediation of arsenic (As) contamination in soil, the use of microorganisms to efficiently reduce As and their assessment of genetic erosion by DNA damage using genomic template stability (GTS) evaluation and using RAPD markers were investigated. The five sites examined for microorganisms and contaminated soils were collected from affected gold mining areas. The highest As concentration in gold mining soil is 0.72 mg/kg. Microorganism strains isolated from the gold mining soil samples were tested for As removal capacity. Two bacterial isolates were identified by 16S rRNA gene sequence analysis and morphological characteristics as Brevibacillus reuszeri and Rhodococcus sp. The ability to treat As in nutrient agar (NA) at 1,600 mg/L and contaminated soil samples at 0.72 mg/kg was measured at 168 h, revealing more efficient As removal by B. reuszeri than Rhodococcus sp. (96.67% and 94.17%, respectively). Both species have the capacity to remove As, but B. reuszeri shows improved growth compared to the Rhodococcus sp. B. reuszeri might be suitable for adaptation and use in As treatment. The results are in agreement with their genetic erosion values, with B. reuszeri showing very little genetic erosion (12.46%) of culture in As concentrations as high as 1,600 mg/L, whereas 82.54% genetic erosion occurred in the Rhodococcus sp., suggesting that Rhodococcus sp. would not survive at this level of genetic erosion. Therefore, B. reuszeri has a high efficiency and can be used for soil As treatment, as it is capable to tolerate a concentration of 0.72 mg/kg and as high as 1,600 mg/L in NA.
The paper deals with susceptibility of nodular cast iron with ferritic -pearlitic matrix on cavitation erosion . Cavitation tests were carried out with the use of a cavitation erosion vibratory apparatus employing a vibration exciter operated at frequency of 20 kHz. The study allowed to determine the sequence of subsequent stages in which microstr ucture of cast iron in superficial regions is subject to degradation. The first features to be damaged are graphite precipitates. The ferritic matrix of the alloy turned out to be definitely less resistant to cavitation erosion compared to the pearlitic matrix component.
The paper presents the capabilities of welding techniques to creating properties of wear resistant high chromium cast iron alloy. The use
of the right kind of welding sequence allows you to change the structure and properties of the obtained welds. Tests were conducted for
one type of additive material in the form of self shielded core wire. In order to determine the effect of the type of welding sequence on the
properties of welds performed welding using string bead and weave bead. The resulting weld was tested on hardness and research structure
in an optical microscope. In the following studies have been made erosive tests wear of made hardfacing. String beads gave structure rich
in carbides and harder about 270 HV of the weld with weave bead. Also, wear resistance was nearly twice as better for welds made with
string beads. In the experiment a decisive role in the resistance to wear plays a high hardness of the deposit and the presence of carbides in
its structure. Changes in the basic parameters of the deposition process allows for the formation of structure and properties of hardfacing
welds in a wide range.
The sintered stainless steels of different microstructures (austenitic, ferritic and duplex) were laser surface alloyed with hard powders (SiC, Si3N4) and elemental alloying powders (Cr, FeCr, FeNi) to obtain a complex steel microstructure of improved properties. Laser surface alloying (LSA) involved different strategies of powder placing: the direct powder feeding to the molten metal pool and filling grooves machined on the sample surface by powder, and then laser surface melting. Obtained microstructures were characterised and summarised, basing on LOM, SEM and XRD analysis. The links between base material properties, like superficial hardness and microhardness, derived microstructures and erosion resistance was described. The LSA conditions and alloying powder placement strategies on erosion resistance was evaluated. The erosion wear is lower for Cr, FeCr, FeNi laser alloying, where powders were dissolved in the steel microstructure, and hard phases were not precipitated. Precipitations of hard phases (carbides, silicides, martensite formation) reduce erosion resistance of SiC alloyed stainless steel. The LSA with Si3N4 works better due to lack of precipitates and formation of a soft and ductile austenitic microstructure. The erosion wear at the impingement angle of 90° is high for hard and therefore brittle surface layers obtained as a result of alloying by hard particles (SiC, Si3N4). The softer and ductile austenitic stainless steel resist better than harder ferritic and duplex stainless steel material at studied erodent im pingement angle.