This research explored different types of two-phase flow patterns that influenced heat transfer rate by assessing rectangular two-phase closed thermosyphon (RTPCT) made from glass with the sides of equal length of 25.2 mm, aspect ratio 5 and 20, evaporation temperature of 50, 70, and 90 °C, working substance addition rate of 50% by volume of evaporator, and water inlet temperature at condensation of 20 °C. Upon testing with aspect ratios 5, three flow patterns emerged which were: bubble flow, slug flow and churn flow respectively. As per the aspect ratio 20, four flow patterns were discovered which were: bubble flow, slug flow, churn flow and annular flow, respectively. Aspect ratio 5 pertains characteristic which resulted in a shorter evaporation rate of the RTPCT than that of the aspect ratio 20, thus, a shorter flow distance from the evaporator section to heat releaser was observed. Therefore, flow patterns at aspect ratio 5 exhibited a faster flow velocity than that of the aspect ratio 20. Furthermore, changes of flow pattern to the one that is important for heat transfer rate can be easily achieved. Churn flow was the most important type of the flow for heat transfer, followed by slug flow. Moreover, with aspect ratio 20, annular flow was the most important flow for the heat transfer, followed by churn flow, respectively. Throughout the test, average heat flux as obtained from the aspect ratio 5 were 1.51 and 0.74 kW/m2 which were higher than those of the aspect ratio 20. The highest heat flux at the operating temperature of the evaporator section was 90 °C, which was equivalent to 2.60 and 1.52 kW/m2, respectively.
This paper presents the results of experimental testing of parameters of the flow of an agitated liquid in a stirred tank with an eccentrically positioned shaft and with a Rushton turbine. The investigations were focused on the impact of the stirrer shaft shift in relation to the stirred tank vertical axis on the agitated liquid mean velocities and the liquid turbulent velocity fluctuations, as well as on the turbulence intensity in the tank. All the experiments were carried out in a stirred tank with the inner diameter of 286 mm and a flat bottom. The adopted values of the shaft eccentricity were zero (central position) and half the tank radius. The liquid flow instantaneous velocities were measured using laser Doppler anemometry.
Aim: The aim of this study was to analyze the effect of bovine follicular fluid on the survival, morphology and kinetic parameters of bovine thawed spermatozoa under laboratory conditions.
Materials and methods: The semen from 5 bulls of proven fertility was incubated in follicular and physiological fluid for 8 hours. During this time assessment using the CASA system was performed. At the beginning and the end of incubation process evaluation by flow cytometry was conducted.
Results: The results of the sperm motility assessment showed a significant decrease in the analyzed parameters both in the follicular and physiological fluid. A significant reduction in all parameters characterizing movement properties in the semen incubated in the follicular fluid was found. In the physiological fluid, a similar trend was demonstrated only for the following proper- ties: VAP, VSL, VCL, ALH, BCF. A significant difference was found for both fluids in: VCL (p=0.026), ALH (p=0.038) and LIN (p<0.001) at the beginning of incubation. The results of the plasma membrane integrity assessment showed a statistically significant increase in the percent- age of dying sperm at the 8th hour of the incubation in the follicular fluid. In the case of semen incubation in physiological fluid, a statistically significant decrease in the percentage of live non-damaged cells was found with a simultaneous increase in the subpopulation of undamaged dead cells.
Conclusions: Follicular fluid rapidly accelerates the capacitation process. The results of flow cytometry support the hypothesis concerning the ability of follicular fluid to prolong sperm sur- vival.
The image analysis consists in extracting from the information which is available to the observer of the part that is important from the perspective of the investigated process. This process usually accompanies a considerable reduction in the amount of information from the image. In the field of two-phase flows, computer image analysis can be used to determine flow and geometric parameters of flow patterns. This article presents the possibilities of using this method to determine the void fraction, vapor quality, bubble velocity and the geometric dimensions of flow patterns. The use of computer image analysis methods is illustrated by the example of HFE 7100 refrigerant methoxynonafluorobutane condensation in a glass tubular minichannel. The high speed video camera was used for the study, and the films and individual frames received during the study were analyzed.