The Copper-SiC composite was investigated with the help of FEM. The authors modeled and analyzed the effect of relaxation of thermal stresses due to seasoning at room temperature after the manufacturing process together with the effect of thermal stresses induced by reheating the material to a service temperature. Especially, hypothetical fracture at interface was of interest. It was shown that, for a fixed temperature, a single crack emanating at 0° or 45° azimuth would develop only along a portion of fiber perimeter, and a further growth would require stress increase in the fiber surrounding.
NiTi alloys are successfully used in engineering and medical applications because of their properties, such as shape memory effect, superelasticity or mechanical strength. A composite with Mg matrix, due to its vibration damping properties, can be characterized by low weight and good vibration damping properties. In this study, a combination of two techniques was used for successful fabrication of Mg composite reinforced by NiTi alloy preform. The porous preforms synthesized by Self-propagating High-temperature Synthesis (SHS) from elemental powders were subsequently infiltrated with Mg by squeeze casting. The effects were examined with scanning electron microscope with EDS detector, X-ray diffraction and microindentation. The inspection has shown well-connected matrix and reinforcement; no reaction at the interface and open porosities fully infiltrated by liquid Mg. Moreover, analysis of samples’ fracture has exhibited that crack propagates inside the Mg matrix and there is no detachment of reinforcement.
Copper have always been an important material and incorporation of elements into copper for property enhancement. Bronze is a relevant cuprous alloy which is important for many industrial and automotive applications like bearings and machineries. The present research is directed towards the fabrication and tribological analysis of regular bronze (Cu-6Sn) and metal matrix composites reinforced with varying particle sized SiC ceramic reinforcement (30, 35 and 40 μm). The developed specimens were subjected to wear analysis according to ASTM standards, to identify the tribological properties utilizing a pin on disk tribometer. It was noted that the wear rates of developed MMC’s phenomenally decremented with an increase in size of SiC particle reinforcement. Also, the test parameters were influential in altering the wear rates to notable margins. The standard scanning electron microscopy techniques aided in identifying the influence of adhesive wear on the specimen surface.
This paper presents the results of studies concerning the production and characterization of Al-SiC/W and Cu-SiC/W composite materials with a 30% volume fraction of reinforcing phase particles as well as the influence of corrosion and thermal shocks on the properties of selected metal matrix composites. Spark plasma sintering method (SPS) was applied for the purpose of producing these materials. In order to avoid the decomposition of SiC surface, SiC powder was coated with a thin tungsten layer using plasma vapour deposition (PVD) method. The obtained results were analysed by the effect of the corrosion and thermal shocks on materials density, hardness, bending strength, tribological and thermal properties. Qualitative X-ray analysis and observation of microstructure of sample surfaces after corrosion tests and thermal shocks were also conducted. The use of PVD technique allows us to obtain an evenly distributed layer of titanium with a constant thickness of 1.5 µm. It was found that adverse environmental conditions and increased temperature result in a change in the material behaviour in wear tests.
The aim of this work is the development of Cu-Al2O3 composites of copper Cu-ETP matrix composite materials reinforced by 20 and 30
vol.% Al2O3 particles and study of some chosen physical properties. Squeeze casting technique of porous compacts with liquid copper
was applied at the pressure of 110 MPa. Introduction of alumina particles into copper matrix affected on the significant increase of
hardness and in the case of Cu-30 vol. % of alumina particles to 128 HBW. Electrical resistivity was strongly affected by the ceramic
alumina particles and addition of 20 vol. % of particles caused diminishing of electrical conductivity to 20 S/m (34.5% IACS). Thermal
conductivity tests were performed applying two methods and it was ascertained that this parameter strongly depends on the ceramic
particles content, diminishing it to 100 Wm-1K-1 for the composite material containing 30 vol.% of ceramic particles comparing to 400
Wm-1K-1 for the unreinforced copper. Microstructural analysis was carried out using SEM microscopy and indicates that Al2O3 particles
are homogeneously distributed in the copper matrix. EDS analysis shows remains of silicon on the surface of ceramic particles after
binding agent used during preparation of ceramic preforms.
Metal matrix composites (MMC) are finding application in many fields such as aerospace and automobile industries. This is due to their advantages such as light weight and low cost. Among all the available non-traditional machining processes, wire electric discharge machining (WEDM) is found to be a suitable method for producing complex or intricate shapes in composite materials. In this study, an aluminum metal matrix composite (AMMC) with 6% and 8% weight (wt) fraction of Al2O3 is prepared through the stir casting process. The fabricated AMMC specimen is machined using WEDM, considering various process parameters such as wt % of reinforcement, gap voltage (Vg), peak current (IP) wire tension (WT) and dielectric pressure (Pd). Output responses such as the machining rate (MR) and surface roughness (Ra) of the slots are analyzed by conducting L18 mixed orthogonal array (OA) experiments. The experiments are analyzed using techniques for order preference by similarity to ideal solution (TOPSIS) and analysis of variance (ANOVA). Based on the analyses, the optimum combination of process parameters for better MR and Ra is as follows: wt % = 6 gm, Vg = 53 V, Ip = 8 A, WT = 11 g, Pd = 13 bar. The optimum level of process parameters for MR and Ra are 1.5 mm/min and 3.648 µm, respectively. Based on ANOVA, the peak current is found to have a significant influence on MR and Ra. Moreover, based on a scanning electron microscope (SEM) image, the presence of micro-ridges, reinforcement, micro-craters, micro-cracks, recast layers and oxide formation are all analyzed on the surface being machined.
The influence of boron carbide and tungsten carbide on the apparent porosity, density, coercive force, hardness and microstructure of metal matrix composite of the Ferro-TiC type, is presented in this paper. The samples of investigated steel/titanium carbide composite were produced by powder metallurgy process, i.e. by powders mixing and compacting followed by sintering in the vacuum furnace. According to the results, steel/titanium carbide composite materials with addition up to 11.9 vol.% of boron carbide are interesting to detailed investigation as well as materials having more than 17.2 vol.% of tungsten carbide because these compositions show significant changes in hardness and coercive force values.