A study was undertaken to investigate the effects of crumb rubber on the strength and mechanical behaviour of Rubberized cement soil (RCS). In the present investigation, 26 groups of soil samples were prepared at five different percentages of crumb rubber content, four different percentages of cement content and two different finenesses of crumb rubber particle. Compressive strength tests were carried out at the curing age of 7 days, 14 days, 28 days and 90 days. The test results indicated that the inclusion of crumb rubber within cement soil leads to a decrease in the compressive strength and stiffness and improves the cement soil’s brittle behaviour to a more ductile one. A reduction of up to 31% in the compressive strength happened in the 20% crumb content group. The compressive strength increases with the increase in the cement content. And the enlargement of cement content is more efficient at low cement content.
Fuzzy logic determination of the material hardening parameters based on the Heyer’s method was applied in this research. As the fuzzy input variables, the length of two measuring bases and the maximum force registered in the Heyer’s test were used. Firstly, the numerical experiment (the simulation of the fuzzification of the input data) with the assumed disturbance of input variables was performed. Next, on the basis of experimental investigations (eleven samples made from the same material), the membership functions associated with the input data were created. After that, the fuzzy analysis was examined. Fuzzy material hardening constants obtained by means of the α-level optimization and the extension principle methods were compared. Discrete values of the hardening data are found in the defuzzification process, by application of the mass center method.
The paper presents the results of research on the plastic zones formation in thin (3.51 [mm]) shields made of steel C45 with holes of 4, 10 and 20 diameters. The authorship method of identifying plastic macro-strains utilizing optical interference phenomenon was used in the experiments. The basic idea of the method is summarized below as being: “The occurrence of plastic deformations in the active process of loading is testified by a loss of the interference fringes that were previously present or by a clear and rapid change in their character”. In the experiments, the values of the stress initiating the first plastic deformation were determined. In order to explain the processes of plastic deformation appearance a detailed stress state analysis in the holes surrounding area was realized with the use of Finite Element Method. Comparison of experimental results with the results of FEM calculations indicates that there are significant quantitative as well as qualitative differences. Namely stresses initiating plastic deformations clearly exceed the value of ReH, and plastic deformation are of local plastic slides character. Similar results were previously obtained in studies on the shields made of steel 15CrMo with holes.
Prof. Małgorzata Kossut of the Nencki Institute of Experimental Biology talks about brain plasticity, the mechanisms of learning, and the mysteries of forgetfulness.
Numerical analysis of the tensioning cables anchorage zone of a bridge superstructure is presented in this paper. It aims to identify why severe concrete cracking occurs during the tensioning process in the vicinity of anchor heads. In order to simulate the tensioning, among others, a so-called local numerical model of a section of the bridge superstructure was created in the Abaqus Finite Element Method (FEM) environment. The model contains all the important elements of the analyzed section of the concrete bridge superstructure, namely concrete, reinforcement and the anchoring system. FEM analyses are performed with the inclusion of both material and geometric nonlinearities. Concrete Damage Plasticity (CDP) constitutive relation from Abaqus is used to describe nonlinear concrete behaviour, which enables analysis of concrete damage and crack propagation. These numerical FEM results are then compared with actual crack patterns, which have been spotted and inventoried at the bridge construction site.
The paper presents research results on the selection of parameters for the asymmetric rolling process of bimetallic plates 10CrMo9-10 + X2CrNiMo17-12-2. They consisted in determining the optimum parameters of the process, which would be ensured to obtain straight bands. Such deformation method introduces in the band the deformations resulting from shear stress, which affect changes in the microstructure. But their effect on the structure is more complicated than in the case of homogeneous materials. It has been shown that the introduction of asymmetric conditions into the rolling process results in greater grain refinement in the so-called hard layer. There was no negative effect on the structural changes in the soft layer observed.
2-phase composites are often used for high demanding parts that can undergo impact loads. However, most of the papers on dynamic loading concerns layered composites. In our opinion, the impact loads are not considered thoroughly enough. Good examples of 2-phase composites are: (1) a WC/Co cermet or (2) a monolithic ceramic Al2O3/ZrO2. The WC/Co cermet is often modelled as having ductile elasto-plastic Co matrix and ideally elastic WC grains. It is because of very high crushing resistivity of the WC.
In this paper, we present an extension to earlier elaborated models ([44]) with the assumption of ideal elasticity of the grains. The new and general numerical model for high-velocity impact of the 2-phase composites is proposed. The idea of this novelty relies on the introduction of crushability of grains in the composite and thermo-mechanical coupling. The model allows for description of the dynamic response both composite polycrystals made of: (1) 2 different purely elastic phases (e.g. Al2O3/ZrO2) or (2) one elastic phase and the second one plastic (e.g. cermet WC/Co), or (3) 2 elasto-plastic phases with different material properties and damage processes. In particular, the analysis was limited to the cases (2) and (3), i.e. we investigated the WC/Co polycrystal that impacted a rigid wall with the initial velocity equal to 50 m/s.