The aim of this work was to investigate the influence of distilled water flowrate in two different porousmembrane modules on the size of generated nitrogen nanobubbles. Modules had different diameter and number of membrane tubes inside the module. As bubbles are cut off from the membrane surface by a shear stress induced by the liquid flow, the change in the linear liquid velocity should result in a change of the generated bubble diameter. For both modules, higher flowrate of liquid induced generation of smaller bubbles, which was consistent with our expectations. This effect can help us in generation of bubbles of desired size.
This paper presents the results of experimental drum granulation of silica flour with the use of wetting liquids with different values of surface tension. Additionally, different liquid jet breakup and different residual moisture of the bed were applied in the tests. The process was conducted periodically in two stages: wetting and proper granulation, during which no liquid was supplied to the bed. The condition of the granulated material after the period of wetting (particle size distribution and moisture of separate fractions) and a change in the particle size distribution during the further conduct of the process (granulation kinetics) were determined.
The paper presents validation tests for method which is used for the evaluation of the statistical distribution parameters for 3D particles’ diameters. The tested method, as source data, uses chord sets which are registered from a random cutting plane placed inside a sample space. In the sample space, there were individually generated three sets containing 3D virtual spheres. Each set had different Cumulative Distribution Function (CDF3) of the sphere diameters, namely: constant radius, normal distribution and bimodal distribution as a superposition of two normal distributions. It has been shown that having only a chord set it is possible, by using the tested method, to calculate the mean value of the outer sphere areas. For the sets of data, a chord method generates quite large errors for around 10% of the smallest nodules in the analysed population. With the increase of the nodule radii, the estimation errors decrease. The tested method may be applied to foundry issues e.g. for the estimation of gas pore sizes in castings or for the estimation of nodule graphite sizes in ductile cast iron.
The main topic of this study is the experimental measurement and mathematical modelling of global gas hold-up and bubble size distribution in an aerated stirred vessel using the population balance method. The air-water system consisted of a mixing tank of diameter T = 0.29 m, which was equipped with a six-bladed Rushton turbine. Calculations were performed with CFD software CFX 14.5. Turbulent quantities were predicted using the standard k-ε turbulence model. Coalescence and breakup of bubbles were modelled using the homogeneous MUSIG method with 24 bubble size groups. To achieve a better prediction of the turbulent quantities, simulations were performed with much finer meshes than those that have been adopted so far for bubble size distribution modelling. Several different drag coefficient correlations were implemented in the solver, and their influence on the results was studied. Turbulent drag correction to reduce the bubble slip velocity proved to be essential to achieve agreement of the simulated gas distribution with experiments. To model the disintegration of bubbles, the widely adopted breakup model by Luo & Svendsen was used. However, its applicability was questioned.
The purpose of the studies was to estimate efficiency of delivering nebulised drugs into the lower respiratory tract through endotracheal tubes (ET tubes) which are commonly used in the treatment of uncooperative patients. Water solution of Disodium Cromoglycate (DSCG) was nebulised with a constant air flow (25 l/min). Experimental studies were done for eight ET tubes with varying sizes (internal diameter, length) and made of two different materials. Size distribution of aerosol leaving ET tubes was determined with the use of aerosol spectrometer. Fine Particle Fraction (FPF) and Mass Median Aerodynamic Diameter (MMAD) were calculated for the aerosol leaving each tube. Additionally, mass of the Disodium Cromoglycate deposited into each endotracheal tube was determined. ET tubes can significantly influence the parameters of delivered aerosol depending on their diameter. FPF of aerosol delivered in to the respiratory tract is lower if small endotracheal tubes are used. However, MMAD and FPF for large endotracheal tubes are almost identical with MMAD and FPF from nebuliser. The results indicate that a substantial fraction of large droplets is eliminated from the aerosol stream in long endotracheal tubes (270 mm). In this case the mass of drug delivered through ET tubes is reduced but the content of small droplets increases (high value of FPF).
The determination of the form of a probability density function (PDF3) of diameters for nodular particles by using a probability density function (PDF2), which form is empirically estimated from cross-sections of these nodules in a metallographic specimen, can be regarded as a special case of Wicksell's corpuscle problem (WCP). The estimation of the PDF3 for the nodular particles provides information about the kinetics of these particles nucleation, and so about the kinetics of their growth. This information is essential for building more accurate mathematical models of the alloy crystallization. In the paper there are presented two derivations of the methods used for the estimation of the PDF3 form. The first method bases on diameters received from a planar cross-section. The second one uses also data from the planar cross-section but not the diameters only chords. Both methods provide practical rules for the analysis of the empirical diameters’ and chord’s size distribution and allow to estimate the mean value of the external surface area of the particles.
The analysis of particle size in suspensions carried out with use of the laser diffraction method enables us to obtain not only information about the size of particles, but also about their properties, shape and spatial structure, determined basing on fractal dimension. The fractal dimension permits the evaluation of the interior of aggregates, at the same time showing the degree of complexity of the matter. In literature, much attention is paid to the evaluation of the fractal dimension of flocs in activated sludge, in the aspect of control of single processes, i.e. sedimentation, dehydration, coagulation or flocculation. However, results of research concerning the size of particles and the structure of suspensions existing in raw and treated sewage are still lacking. The study presents optical fractal dimensions D3 and particle size distributions measured with use of laser granulometer in raw and treated sewage and activated sludge collected from six mechanical-biological wastewater treatment plants located in the Lower Silesian region. The obtained test results demonstrate that wastewater treatment plants that use both sequencing batch reactors and continuous flow reactors are more efficient at capturing suspension particles of a size up to 30 μm and are characterized by an increased removal of particles of a size ranging from 30 μm to 550 μm to the outflow. Additionally, in the case of samples of treated sewage and activated sludge collected at the same location, at short intervals, similar particle distributions were observed. As far as the analysis of fractal dimensions is concerned, particles contained in the raw sewage suspension were characterized by the lowest values of the fractal dimension (median equals 1.89), while the highest values occurred in particles of activated sludge (median equals 2.18). This proves that the spatial structure of suspension particles contained in raw sewage was similar to a linear structure, with a large amount of open spaces, while the structure of particles contained in the activated sludge suspension was significantly more complex in the spatial aspect.
Feasibility of a model of gas bubble break-up and coalescence in an air-lift column enabling determination of bubble size distributions in a mixer with a self-aspirating impeller has been attempted in this paper. According to velocity measurements made by the PIV method with a self-aspirating impeller and Smagorinski’s model, the spatial distribution of turbulent energy dissipation rate close to the impeller was determined. This allowed to positively verify the dependence of gas bubble velocity used in the model, in relation to turbulent energy dissipation rate. Furthermore, the range of the eddy sizes capable of breaking up the gas bubbles was determined. The verified model was found to be greatly useful, but because of the simplifying assumptions some discrepancies of experimental and model results were observed.
The objective of this investigation was comparing the penetration of chloride ions in ordinary and air-entrained concretes containing a waste material Fluidized Bed Combustion Fly Ash (FBCFA). All concretes were tested with 15% and 30% cement replacement by FBCFA, with the same water-binder ratio of 0.45. Two kinds of fly ash coming from fluid bed combustion in two power plants in Poland have been used.
In this study the rapid chloride permeability test – Nordtest Method BUILD 492 method – was used. The microstructure of the concrete was analyzed on thin polished sections and the measurement of air voids sizes and their distribution, using digital image analysis, was carried on according to PN-EN 480-11:2008.
Obtained results have shown a significant influence of partial cement replacement by FBCFA on the chloride ions movements in concrete. It has been found that this kind of addition reduced considerably the chloride ion penetration. The influence of air entrainment on the chloride diffusion coefficients was also measured and it was shown that application of air-entraining admixture for concretes with FBCFA reduce the chloride diffusion coefficient but it should be used with caution.
Complex circuit of milling-classify systems are used in different branches of industry, because the required particle size distribution of product can seldom be reached in a single-stage grinding on the same device. The multistage processes of comminution and classification make possible suitable selection of parameters process for variables graining of fed material, mainly through sectioning of devices or change of their size and the types. Grinding material usually contains size fractions, which meet the requirements relating finished product. Then profitable is preliminary distributing material on a few size fractions, so to deal out with them demanded fraction of product, whereas remaining to direct alone or together with fed material to the same or different device. If the number of mills and classifiers in a circuit is large enough, building the model of particle size distribution transformation becomes rather complicated even for the circuit of a given structure. The situation becomes much more complicated, if we want to compare characteristics of all possible circuits, that can be constructed from these mills and classifiers, because the number of possible circuits increases greatly with the increase of number of devices being in the milling-classify system. The method creating matrix model for transformation of particle size distribution in a circuit of arbitrary structure of milling-classify system is presented in the article. The proposed model contains the mass population balance of particle equation, in which are block matrices: the matrix of circuit M, the matrix of inputs F and the matrix of feed F0. The matrix M contains blocks with the transition matrix P, the classification matrix C, the identity matrix I and the zero matrix 0 or elements describing the transformation of particle size distribution in the circuit. The matrix F is the block column matrix, which elements describing all particle size distributions at inputs to the circuit elements. The matrix F0 is the block column matrix, which elements describing particle size distributions in all feeds to the circuit. In paper was discussed this model in details, showed algorithm and three examples formatrix construction for the closed circuit ofmilling-classify systems. In conclusion was affirmed, that presented model makes possible to forecasting particle size distribution of grinding product, which leaving chosen the unit of system. The matrix model can be applied to improving modeling of mineral processing in the different grinding devices.
Arid areas are particularly susceptible to soil erosion due to long dry periods and sudden heavy downpours. This study investigates the aggregate size distribution and aggregate stability of twelve tilled fallow areas of Hyderabad district, Sindh, Pakistan. This study determined aggregate size distribution by dry sieving to evaluate the seedbed condition and aggregate stability using wet sieving to assess the susceptibility of tilled fallow areas to soil erosion. The aggregate size distribution of the soils of the selected areas was highly variable. Gulistan-e-Sarmast had the largest number of clods (51.0%) followed by Kohsar (49.0%), Latifabad # 10 (41.10%) and Daman-e-Kohsar (39.0%). Fazal Sun City, the left side of the Indus River, the Village Nooral Detha and the left side of the Abdullah Sports city had a greater number of large (>8.0 mm) and small aggregates (<0.5 mm). The optimum aggregate size distribution was found in the left side of the channel, which had the largest number of aggregates (50.50%) in the 0.5–8.0 mm sieve size range. Maximum aggregate stability (AS) was found in Gulistan-e-Sarmast (46%), Kohsar (42%) and Latifabad # 10 (34%), while all other soils had minimum aggregate stability (<14%). The minimum aggregate stabilities demonstrate that the tilled fallow areas of Hyderabad district are highly susceptible to erosion. Therefore, the present study suggests investigating potential ways to enhance the aggregate stabilities of soils.
There are 40 coal mines in Poland now. One of them (coal mine “Bogdanka”) is situated in Lublin Coal Basin, other are localised in Silesia and Małopolska regions. Coal mining is a source of large amounts of wastes. Mean annual production of wastes in only Lublin Coal Basin exceeds 2 million Mg, 65% of which is disposed on a heap. The rest is used to restore opencast excavations, to construct and repair local roads and to produce building materials. It seems that large amount of these wastes could be used to construct or modernize flood embankments and dykes. Using mine wastes as building materials requires the knowledge of their geotechnical parameters. A characteristic feature of mine wastes is their gradual weathering which affects geotechnical parameters largely determined by their mineral and petrographic composition.
This paper describes analyses of geotechnical parameters of mine wastes from Lublin Coal Basin (heap near coal mine “Bogdanka”) of various storage times and of samples collected after 10 years of exploitation of a dyke between ponds made of these wastes at the break of 1993 and 1994. Detailed analyses involved: grain size distribution, natural and optimum moisture content, maximum dry den-sity, shear strength and coefficient of permeability. Obtained results were compared with literature data pertaining to mine wastes from Upper Silesian Coal Basin and from other European coal basins.
Performed studies showed that coal mining wastes produced in Lublin Coal Basin significantly differed in the grain size distribution from wastes originating from Upper Silesian Coal Basin and that weathering proceeded in a different way in wastes produced in both sites.