This study focuses to develop a new hybrid Engineered Cementitious Composite (ECC) and assesses the performance of a new hybrid ECC based on the steel short random fiber reinforcement. This hybrid ECC aims to improve the tensile strength of cementitious material and enhance better flexural performance in an RC beam. In this study, four different mixes have been investigated. ECC with Poly Vinyl Alcohol (PVA) fiber and PolyPropylene (PP) fiber of 2.0% volume fraction are the two Mono fiber mixes; ECC mix with PVA fiber of 0.65% volume fraction hybridized with steel fiber of 1.35% volume fraction, PP fiber of 0.65% volume fraction hybridized with steel of 1.35% volume fraction are the two additional different hybrid mixes. The material properties of mono fiber ECC with 2.0 % of PVA is kept as the reference mix in this study. The hybridization with fibers has a notable achievement on the uniaxial tensile strength, compressive strength, Young’s modulus, and flexural behavior in ECC layered RC beams. From the results, it has been observed that the mix with PVA fiber of 0.65% volume fraction hybrid with steel fiber of 1.35% volume fraction exhibitimprovements in tensile strength, flexural strength, andenergy absorption. ThePP fiber of 0.65% volume fraction hybridized with steel of 1.35% volume fraction mix has reasonable flexural performance and notable achievement in displacement ductility overthe reference mix.
The strength of recycled aggregate (RA) is low, which makes the performance of recycled aggregate concrete (RAC) poor, and the addition of fiber can make up for the shortcoming of RAC. In this paper, the mechanical properties of RAC which was added with steel fiber were studied. The specimens with RA content of 0%, 40%, 70% 100% and steel fiber content of 0%, 0.5% and 1% were prepared, and their mechanical properties were tested. The results showed that the slump reduced 73.75% after the addition of 100% RA and 37.5% after the addition of 1% steel fiber compared to R0S0; from the perspective of mechanical properties, the larger the content of steel fiber, the better the mechanical properties of the specimen; the improvement of the tensile strength was the most obvious after the addition of steel fiber. The experimental results show that steel fiber can improve the performance of RAC and make it perform better in practical application.
Experimental tests were carried out to assess the failure model of steel and basalt fiber reinforced concrete two-span beams. Experimental research was focused on observing the changes in behavior of tested elements in dependence on the ratio of shear reinforcement and type of fiber. The beams had varied stirrup spacing. The steel fiber content was 78.5 kg/m3 (1.0% by vol.) and basalt fiber content was 5.0 kg/m3 (0.19% by vol.). Concrete beams without fibers were also examined. Two-span beams with a cross-section of 120×300 mm and a length of 4150 mm were loaded in a five-point bending test. Shear or flexural capacity of tested members was recorded. The effectiveness of both sorts of fibers as shear reinforcement was assessed and the differences were discussed. It was shown that fibers control the cracking process and the values of deflections and strains. Fibers clearly enhance the shear capacity of reinforced concrete beams.
Confinement in concrete can improve the descending branch of the stress-strain relationship of concrete. The addition of steel fiber in concrete can also improve the descending branch of the stress-strain relationship of concrete. The combination of the use of both can double the impact significantly on the post-peak response. It can be seen from the trend of the post-peak response that the values of both 0.85fccf and 0.5fccf can be well predicted. The study involved an experimental investigation on the effect of confinement on square column specimens reinforced with steel fiber. From the experimental program, it is proven that the use of combination of confining steel and steel fiber works very well which is indicated by the better improvement on the post-peak response. The proposed equations can predict the actual stress-strain curves quite accurately which include the effects of confinement parameters (Zm) and steel fiber volumetric parameter (Vf).