Ultra-precision testing is a very important procedure to secure the reliability of the products as well as for the technology development in the areas of semiconductor and display. Accordingly, companies manufacturing equipment for testing of semiconductor and display have been continuously executing researches for the improvement of the performances of test sockets used in test equipment.
Through this study, characteristics of the materials in accordance with the mechanical and electrical properties of Ni-30wt%Co alloy and newly developed Cu-2wt%Be alloy were analyzed in order to select the probe pin material of the socket, which is a key component used in the semiconductor testing equipment. In addition, finite element interpretation was executed by using Ansys Workbench 14.0 to comparatively analyze the finite element interpretation results and experimental results. Experiment was executed for the mechanical properties including tensile strength, elasticity modulus, specific heat, thermal expansion coefficient and Contact Force, for electrical properties, experiment on surface resistance, specific resistance and electrical conductivity was executed to measure the properties. It was confirmed that the results of finite element interpretation and experiment displayed similar trend and it is deemed that the Contact Force value was superior for Be-Co alloy.
Through this study, it was confirmed that the newly developed Be-Co alloy is more appropriate as probe pin material used as the core component of test socket used in the semiconductor testing equipment than the existing Ni-Co alloy.
The study investigates the effect of heat treatment on the microstructure evolution and properties of an age-hardened Cu-3Ti-2Mg alloy. The precipitated Cu2Mg and β'-Cu4Ti phases consequently yield a depletion of the Cu matrix in regards to Ti and Mg solutes, which enhances the electrical conductivity. The Cu2Mg Laves phase and β'-Cu4Ti phase precipitates increase the hardness of the alloy due to the consistency and coherency of the later phase. However, the decrease of hardness is mainly associated with the coarse microstructures, that can be formed due to the phase transformation from metastable β'-Cu4Ti phase to more stable Cu3Ti phase. In the range of experiments, the optimum process is solution treatment at 700°C for 4 h, with subsequent age-hardening at 450°C for 4 h. The electrical conductivity, hardness, tensile strength, and elongation of the Cu-3Ti-2Mg alloy were 15.34 %IACS, 344 HV, 533 MPa, and 12%, respectively.
This study was undertaken to investigate the effect of severe plastic deformation (SPD) by extrusion combined with reversible torsion (KoBo) method on microstructure and mechanical properties of Al-5Cu and Al-25Cu alloys. The extrusion combined with reversible torsion was carried out using reduction coefficient of λ = 30 and λ = 98. In this work, the microstructure was characterized by light microscopy (LM), scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM). Compression test and tensile test were performed for deformed alloys. The binary Al-5Cu and Al-25Cu alloys consist of the face cantered cubic (FCC) α phase in the form of dendrites and tetragonal (C16) θ-Al2Cu intermetallic phase observed in interdentritic regions. The increase of Cu content leads to increase of interdentritic regions. The microstructure of the alloys is refined after applying KoB deformation with λ = 30 and λ = 98. Ultimate Tensile Strength (UTS) of Al-5Cu alloy after KoBo deformation with λ = 30 and λ = 98 reached about 200 MPa. UTS for samples of Al-25Cu with λ = 30 and λ = 98 increased compared to Al-5Cu alloy and exceed 320 MPa and 270 MPa respectively. All samples showed increase of plasticity with increase of reduction coefficient. Independently of reduction coefficient, the compressive strain of Al-5Cu alloys is about 60%. The Al-25Cu alloy with λ = 98 showed the value of compressive strain exceed 60%, although for this same alloy but with λ = 30, the compressive strain is only 35%.
An overview of the bibliography regarding the connection of knowledge about precious metal alloys and aspects of the use of computer aided technologies to the optimization of the jewelry casting processes is presented. An analysis of the usability of selected CAx systems was made: 1) for spatial design, called Rhinoceros 6 and 2) CAE system: NovaFlow & Solid (NF&S). The authors describe own research including data acquisition and evaluation of temperature variations during solidification of the selected Au-Ag-Cu alloy, with the identification of the phase transformations of this alloy. The intensity of heat exchange was changed (cooling of specimens under ambient temperature conditions – "normal" intensity and with the furnace – very slow cooling). The problem of completing the simulation database was pointed out and analyzed. Examples of simulations of casting selected jewelry (ring and signet) were given and compared with the result of the experiment realized in real conditions. It was confirmed that the optimization by combining experimental and simulation studies allows for the acquisition of new knowledge, and also facilitates the creation of new artistic designs of jewelry as well as performing the feasibility check, and then optimizing the chosen technology.
The paper presents the research data on structure, phase composition, defect substructure state, and microhardness of surface layers in the piston alloy Al-10wt%Si-2wt%Cu irradiated by an electron beam with various energy densities and pulse times. An important finding to emerge from the study is that the processing by an electron beam with an energy density of 10 J/cm2 brings about slight surface melting, whereas a weak thermal impact of an electron beam hardly changes the phase composition. Once an energy density of an electron beam is set 30 J/cm2, intermetallic compounds dissolve and numerous micropores arise. Irradiating by an electron beam with an energy density of 50 J/cm2, randomly located microcracks are detected on the treated surface with no regard to a pulse time. A structure of high-speed cellular crystallization with cells from 500 to 600 nm forms in the surface layer. A thickness of the modified layer is related to a beam energy density. As a beam energy density goes up, a thickness of a high-speed cellular crystallization layer increases. Atoms of Si, Cu, Ni, as well as a small quantity of Fe and Mg are detected in the surface, in thin layers surrounding crystallization cells. In a layer 60-80 μm below the irradiated surface, in material between high-speed crystallization cells, there are Si atoms and an insignificant number of Cu atoms. An analysis of a deeper material part has shown a structure similar to the as cast alloy. A drop of microhardness – if compared with the as cast material – is reported at an energy density of 10 J/cm2 because an energy amount supplied by an electron beam to the alloy surface is insufficient for melting of the material and dissolution of the intermetallic phase. A raise of a beam energy density up to 20-50 J/cm2 causes a max increase of microhardness up to 1.13 GPa for 40 J/cm2, 50 s, and up to 1.16 GPa for 40 J/cm2, 200 s.
Comprehensive understanding of the melt quality is of vital importance for foundry man. The effect of each particular element need to be properly analysed. Therefore, the aim of this paper was to analyse the impact of various content of zirconium on the solidification path and structural characteristics (SDAS, grain size, porosity) of as cast commercial AlSi10MgCu alloys. It has been found that addition of zirconium up to 0.24 wt.% reduce significantly the grains size (from 3.5 mm to 1.2 mm), SDAS (from 57.3 µm to 50.4 µm) and porosity (from 19% to 5%), leading to production of sound cast parts.