This investigation was undertaken to determine the optimum conditions for physical-chemical treatment of waste water contaminated with heavy metals in the industry of metallic coatings. The industry uses substances such as: inorganic acids, alkalis, acidic and alkaline metal salts, that has a high water demand in the processes of flushing and cleaning the parts to be coated. According to the preliminary characterization of samples and reported in the literature theory, physico-chemical process was implemented for the removal of contaminants that consisted in chemical oxidation of CN-ions, followed by chemical precipitation made next to a coagulation/flocculation and subsequent adsorption on activated coal. Laboratory scale tests showed the optimal conditions of treatment including chemical oxidation by the addition of 4.15 cm3 of H2O2(30%) per gram of CN, chemical precipitation with NaOH to a pH of 12, followed by coagulation/flocculation with Fe2(SO4)3 at a speed of 135 rpm for 3 min and 20 rpm for 20 min and finally the addition of 1.0 g of adsorbent previously activated at 700°C. From this study, it is clear that the adsorption on activated carbon is highly efficient in the removal ofheavy metals from industrial waste water from electroplating. However, it is also clear that the parallel application of the treatments, shown here, is more effective to completely remove contaminants such as lead, nickel, silver, and copper at la-boratory scale, so it is recommended the simultaneous use of these physico-chemical processes.
In this study, laboratory-scale experiments were carried out to investigate the effects of microwave-assisted alkaline leaching on the treatment of electric arc furnace dusts to recover zinc and lead. Microwave treatment is a new innovative technology in waste treatment and now is an attractive advanced inter-disciplinary field and also environmental friendly. The highest zinc extraction, 50.3% in 60 minutes using 5 M NaOH at 750 W and L:S ratio 20, and lead extraction up to 92.84% was achieved in these same conditions but in 30 minutes. Compared with conventional leaching, the top extraction rate using MW-assisted leaching was higher by 16% (Zn) and 26% (Pb). Zinc presents in the flue dust in the form of franklinite (ZnFe2O4), its leaching in sodium hydroxide does not occur under the examined conditions, because it is enclosed in a matrix of iron.
The fixation of CO2 in the form of inorganic carbonates, also known as mineral carbonation, is an interesting option for the removal of carbon dioxide from various gas streams. The captured CO2 is reacted with metal-oxide bearing materials, usually naturally occurring minerals. The alkaline industrial waste, such as fly ash can also be considered as a source of calcium or magnesium. In the present study the solubility of fly ash from conventional pulverised hard coal fired boilers, with and without desulphurisation products, and fly ash from lignite fluidised bed combustion, generated by Polish power stations was analysed. The principal objective was to assess the potential of fly ash used as a reactant in the process of mineral carbonation. Experiments were done in a 1 dm3 reactor equipped with a heating jacket and a stirrer. The rate of dissolution in water and in acid solutions was measured at various temperatures (20 - 80ºC), waste-to-solvent ratios (1:100 - 1:4) and stirrer speeds (300 - 1100 min-1). Results clearly show that fluidised lignite fly ash has the highest potential for carbonation due to its high content of free CaO and fast kinetics of dissolution, and can be employed in mineral carbonation of CO2.
The present study addresses the utilization of induction furnace steel slag which is an anthropogenic waste, for enhancing the mechanical properties of a commercial aluminium alloy A356. Different weight percentage (3wt%, 6wt%, 9wt%, and 12wt%) of steel slag particles in 1 to 10 μm size range were used as reinforcing particles in aluminium alloy A356 matrix. The composites were prepared through stir casting technique. The results revealed an improvement in mechanical properties (i.e. microhardness and tensile strength) and wear resistance with an increase in weight percentage of the steel slag particles. This research work shows promising results for the utilization of the steel slag for enhancing the properties of aluminium alloy A356 at no additional cost while assisting at same time in alleviating land pollution.
Recycling of plastic wastes helps in reducing waste disposal problems and helps for the sustainable development of the country. Concrete with various % (0 to 55%) of waste plastic aggregates were tested for their mechanical strength properties. In the present work, plastic aggregates obtained as end product of a polymer recycle industry in the form of grains called as plastic aggregates are used as fine aggregate replacements in concrete. The addition of plastic aggregate as fine aggregate replacements results in increase in compressive strength, split tensile strength and flexural strength and thus helps in production of sustainable concrete. It is observed that, the optimum % of replacement of sand with waste plastic waste is 40% and it is also found that upto55% of sand replacements with plastic wastes, mechanical strength values are comparable with that of the normal concrete.