Air abrasion process is used for cleaning casting surface of prosthetic components, and to prepare the surface of these elements for the
application of veneering items. Its side effect, however, is that abrasive particles are embedded in the treated surface, which can be up to
30% of the surface and it constitutes the side effect of this procedure. Such a significant participation of foreign material can not be
indifferent to the properties of the surface. Embedded particles can be the place of stress concentration causing cracking of ceramics, and
may deteriorate corrosion resistance by forming corrosive microlinks. In the latter cases, it would be advisable to remove elements
embedded into the surface. The simplest method is chemical etching or electrochemical one. Nevertheless, these procedures should not
significantly change the parameters of the surface. Among many possible reagents only a few fulfills all the above conditions. In addition,
processing should not impair corrosion resistance of titanium, which is one of the most important factors determining its use as a prosthetic
restoration in the mouth. The study presented results of corrosion resistance of titanium used to make prosthetic components by means of
casting method, which were subjected to chemical processing designed to remove the embedded abrasive particles. The aim of the study
was to investigate whether etching with selected reagents affects the corrosion resistance of titanium castings. For etching the following
reagents were used: 30% HNO3 + 3% HF + H2O, HNO3+ HF+ glycerol (1:2:3), 4% HF in H2O2, 4% HF in H2O, with a control
sandblasted sample, not subjected to etching. Tests demonstrated that the etching affected corrosion properties of test samples, in each case
the reduction of the corrosion potential occurred - possibly due to the removal of particles of Al2O3 from the surface and activation of the
surface. None of the samples underwent pitting corrosion as a result of polarization to 9 V. Values of the polarization resistance, and
potentiodynamic characteristics indicated that the best corrosion resistance exhibited the samples after etching in a mixture of 4% solution
of HF in H2O2. They showed very good passivation of the surface.
The purpose of this study is to investigate a structure’s response to blast loading when composite columns are used instead of conventional reinforced concrete (RC) cross sections and when a conventional structure is retrofitted with braces. The study includes conducting dynamic analyses on three different structures: a conventional reference RC structure, a modified structure utilizing composite columns, and a modified structure retrofitted with steel braces. The two modified structures were designed in order to investigate their performance when subjected to blast loading compared to the conventional design. During the dynamic analyses, the structures were exposed to simulated blast loads of multiple intensities using the finite-element modelling software, SeismoStruct. To evaluate their performance, the responses of the modified structures were analyzed and compared with the response of the conventional structure. It was concluded that both the structure with composite columns and the steel brace structure experienced less damage than the conventional model. The best performance was obtained through the steel brace structure.
In this Paper, a parametric study on pipes buried in soil was performed illustrating the results of blast loading. Effects of various parameters such as the physical properties of water, oil, gas, air, soil, pipes, and TNT have been investigated. The arbitrary Lagrangian-Eulerian (ALE) method was employed using LS-DYNA software. The maximum pressure in a buried pipe explosive was observed at an angle of about 0° to 45° and the minimum pressure occurred at an angle of about 45° to 90°. Therefore, all figures in this study illustrate that fluid pressure levels in buried pipes can help in their stabilization. In generally, by increasing the 1.23 times of liquid density under the explosion, the pressure levels in the soil decreased by 1.3 percent. The gas pressure has been increasing more than oil and water pipes 39.73 and 40.52 percent, respectively.
One of the main purpose of accurate blasting in open pit mining is to achieve optimum rock fragmentation.
The degree of rock fragmentation plays a significant role in order to control and minimise the
overall production cost including loading, hauling and crushing. In the present paper, the application of
a Number-Size (N-S) fractal model is intended to classify the blast fragmentation size in the Jalal-Abad
iron mine, SW Iran, using GoldSize image analysis software for four blasting with the obtained result
being compared with Kuz-Ram curves. To do this, the fractal dimensions via N-S log-log plots were
generated based on the output of the GoldSize software. The results indicated that the fragmented rocks
have a multifractal nature with four/five different fragmented populations in terms of size namely; the fine
rocks with the size of less than 16 cm, Mean-fragment values between 16 and 45 cm, In-range between
45 and 70 cm and finally, oversize larger than 70 cm.
Shot blasting machines are widely used for automated surface treatment and finishing of castings. In shot blasting processes the stream of shots is generated and shaped by blasting turbines, making up a kinetic and dynamic system comprising a separating rotor, an adapting sleeve and a propelling rotor provided with blades. The shot blasting performance- i.e. the quality of shot treated surfaces depends on the actual design and operational parameters of the unit whilst the values of relevant parameters are associated with the geometry of turbine components and the level of its integration with the separator system. The circulation of the blasting medium becomes the integrating factor of the process line, starting from the hopper, through the propeller turbine, casting treatment, separation of contaminated abrasive mixture, to its recycling and reuse. Inferior quality of the abrasive agent (shot) and insufficient purity of the abrasive mixture are responsible for low effectiveness of shot blasting. However, most practitioners fail to fully recognize the importance of proper diagnostics of the shot blasting process in industrial conditions. The wearing of major machine components and of the blasting agent and quality of shot treated surfaces are often misinterpreted, hence the need to take into account all factors involved in the process within the frame of a comprehensive methodology. This paper is an attempt to formulate and apply the available testing methods to the engineering practice in industrial conditions.
Stemming plugs are one of the widely used accessory in surface mining operations. Stemming plugs assist conventional stemming material in gas retention and help in better fragmentation and explosive utilization. Effective use of the stemming plugs results in economic benefits and enhance the efficacy of the project. Economic and productive viability of stemming plugs have been conducted in depth by different researchers. Addition of stemming plugs to a new system requires ergonomic challenges for operators conducting drilling and blasting operation. Induction of a newer product in already established system is subject to overall positive feedback. This work investigates ergonomics of three different stemming plugs introduced to a limestone quarry in Pakistan. The stemming plugs were evaluated based on extra time needed, workers feedback, failures during operation, recovery time after failure and number of extra equipment required to carry out the operation. Points based matrix was established with likeliness of each plug and based on overall scores stemming plug 1 was most acceptable followed by stemming plug 3. Stemming plug 2 was disliked by operation and did not reach the level of acceptability of operators. This work will help stemming plug making industry in adapting to best practices by incorporating ergonomics of plugs in designing. Literature shows no previous work on ergonomics of stemming plugs.
Rice blast is one of the most destructive rice diseases known to cause considerable yield losses globally. Plant growth promoting rhizobacteria (PGPR) and arbuscular mycorrhizal fungi (AMF) are closely associated with rice plants and improve plant growth and health. To determine how isolated bacteria trigger rice growth, an assessment of phosphate solubilization and auxin production mechanisms was carried out in vitro and in vivo. In this study, the interactions between PGPR and Rhizophagus irregularis were evaluated in wildtype and CYCLOPS mutant plants to provide a sustainable solution against blast disease and reduce the amount of yield loss. Importantly, Bacillus subtilis UTSP40 and Pseudomonas fluorescens UTSP50 exhibited a suppressive effect on AMF colonization which shows the probable existence of a functional competition between AMF and PGPR to dominate the rhizosphere. On the other hand, R. irregularis decreased the biocontrol activity of B. subtilis UTSP40 in wild type, although this reduction was not significant in mutant plants. Results showed that the same defense-related genes were induced in the roots of wild type colonized by B. subtilis UTSP40 and R. irregularis. Therefore, plant cell programs may be shared during root colonization by these two groups of beneficial microorganisms.
Rice blast is the main disease of rice plants in Indonesia and several countries worldwide. Controlling this disease using chemical fungicides has harmful effects on the environment. Therefore, we need biocontrol agents which are more environmentally friendly such as rice phyllosphere bacteria. This study aimed to explore bacteria producing bioactive compounds from the rice phyllosphere environment to control blast disease. A total of 88 isolates were successfully isolated from rice leaves in Sukabumi, Situgede, and Jasinga (West Java, Indonesia). From them, we obtained 22 bacteria isolates with antifungal activity against Pyricularia oryzae in vitro assay. In addition, seven non-pathogenic bacteria were obtained from further screening in hypersensitivity, hemolysis and pathogenicity assays, namely STGG 3, STGG 7, STGG 8, STGG 14, SKBV 1, STGV 8, and SKBG 78. To show their antifungal activity, we tested crude extracts of these seven isolates and the results revealed that all the crude extracts can inhibit the growth of P. oryzae. Based on a genetic approach, isolates STGG 3, STGG 7, and STGG 14 were found to have both nonribosomal peptide synthetases (NRPS) and polyketide synthases (PKS) genes, while isolate SKBV 1 only had the NRPS gene. The NRPS and PKS genes from potential isolates were similar to NRPS and PKS genes of Bacillus sp. in different strains. Furthermore, molecular identification based on the 16S rRNA gene revealed that the seven potential isolates belong to three genera, i.e. Bacillus (STGG 3, STGG 7, STGG 8, STGG 14, SKBV 1), Enterobacter (STGV 8) and Brachybacterium (SKBG 78). We suggest that the seven isolates found in this study have potency and could be recommended as biocontrol agents of blast disease caused by P. oryzae.
The major downside of blasting works is blast vibrations. Extensive research has been done on the subject and many predictors, estimating Peak Particle Velocity (PPV), were published till date. However, they are either site specific or global (unified model regardless of geology) and can give more of a guideline than exact data to use. Moreover, the model itself among other factors highly depends on positioning of vibration monitoring instruments. When fitting of experimental data with best fit curve and 95% confidence line, the equation is valid only for the scaled distance (SD) range used for fitting. Extrapolation outside of this range gives erroneous results. Therefore, using the specific prediction model, to predetermine optimal positioning of vibration monitoring instruments has been verified to be crucial. The results show that vibration monitoring instruments positioned at a predetermined distance from the source of the blast give more reliable data for further calculations than those positioned outside of a calculated range. This paper gives recommendation for vibration monitoring instruments positioning during test blast on any new site, to optimize charge weight per delay for future blasting works without increasing possibility of damaging surrounding structures.
In this paper, an attempt was made to find out two empirical relationships incorporating linear multivariate regression (LMR) and gene expression programming (GEP) for predicting the blast-induced ground vibration (BIGV) at the Sarcheshmeh copper mine in south of Iran. For this purpose, five types of effective parameters in the blasting operation including the distance from the blasting block, the burden, the spacing, the specific charge, and the charge per delay were considered as the input data while the output parameter was the BIGV. The correlation coefficient and root mean squared error for the LMR were 0.70 and 3.18 respectively, while the values for the GEP were 0.91 and 2.67 respectively. Also, for evaluating the validation of these two methods, a feed-forward artificial neural network (ANN) with a 5-20-1 structure has been used for predicting the BIGV. Comparisons of these parameters revealed that both methods successfully suggested two empirical relationships for predicting the BIGV in the case study. However, the GEP was found to be more reliable and more reasonable.
Detonation of explosives creates strong para-seismic vibrations. Such vibrations can damage buildings or other infrastructure located in the vicinity of such detonations, and can be burdensome to people living in such areas. This paper describes the usefulness of Matching Pursuit (MP) algorithm in assessing the impact of blasting on the surrounding areas, and proves that by taking into account frequency changes over time, vibration analysis can help make much more profound and reliable predictions in this field.