The aim of this study was to compare and analyze the gasification process of beech wood. The experimental investigation was conducted inside a gasifier, which can be operated in downdraft and updraft gasification system. The most important operating parameter studied in this paper was the influence of the amount of supply air on the temperature distribution, biomass consumption and syngas calorific value. The results show that the amount of air significantly influences the temperature in the combustion zone for the downdraft gasification process, where temperature differences reached more than 150 ◦C.The increased amount of air supplied to the gasifier caused an increase in fuel consumption for both experimental setups. Experimental results regarding equivalence ratio show that for value below 0.2, the updraft gasification is characterized by a higher calorific value of producer gas, while for about 0.22 a similar calorific value (6.5 MJ/Nm3) for both gasification configurations was obtained. Above this value, an increase in equivalence ratio causes a decrease in the calorific value of gas for downdraft and updraft gasifiers.

The purpose of this article is to present three theses – (1) a cultural one: cyberspace is an advanced technical and cultural creation – it is an embodiment of dreams of numerous creators, inventors and engineers; (2) a technical one: security and cyberspace are inseparable components (hence cybersecurity); (3) and a paranoid one: complete security, if achievable, is not a permanent state (hence cyber(in)security). Cyberspace is conceived as a set of digital techniques used to exchange information but also as a new type of social space, partially virtual, which may constitute a being entirely separated from a physical one. A pivotal date for arising of cyberspace may be considered the year 1968 in which routing in the ARPANET network appeared and so did the first programmable logical controller (PLC). For cyberspace this will be the year 1976 – publishing of the key agreement protocol by Witfield Diffie and Martin Hellman. Development of security is correlated with warfare and armament – the military sector has historically made the most significant investments in this area.

The paper deals with an application-specific integrated circuit (ASIC) facilitating voltage conversion in thermoelectric energy harvesters. The chip is intended to be used to boost up the voltage coming from a thermoelectric module to a level that is required by electronic circuits constituting wireless sensor nodes. The designed charge pump does not need any external parts for its proper operation because all the capacitors, switches and oscillator are integrated on the common silicon die. The topography of the main functional blocks and post-layout simulations of the designed integrated circuit are shown in the article.

The article presents tests carried out on three selected samples of limestone originating from three commercially exploited deposits. The tests of sorbents included desulphurisation in different atmospheres and a physicochemical analysis of desulphurisation products. The aim of the tests was to determine desulphurisation efficiency and conversion degree as dependent on the concentration of O2 and CO2.

Whereas the use of biofuels has attracted increasing attention, the aim of this paper is to investigate the possibility of using sewage sludge as biofuel. Preparation of untreated and stabilised sludge with natural additives is described, as well as combusting method applied and experimental results of combusting are presented based on the assessment of composition of emitted pollutants and their concentrations in the exhaust gas. NOx formation in the exhaust gas has been analysed in depth. The results of investigations have shown that the use of dried sewage sludge possesses a positive energy balance. Therefore, the sludge may be used as fuel. The obtained experimental results demonstrate that during combustion, pollutant concentrations vary depending on oxygen content (O2), while formation of nitrogen oxides is strongly influenced by fuel-bound nitrogen. Also, a generalized equation of calculating fuel bound nitrogen conversion into NOx is presented.

This article discusses the issue of hypermodernity, which was studied as part of the research project Poles in the World of Late Capitalism. The article presents biographical models of hypermodernity and strategies of coping with hypermodern ideology, that is, cyclothymias, conversions, and hypermodern episodes.

The development of linear infrastructure increases the degree of fragmentation of natural areas and has a negative impact on biodiversity and the range of available ecosystem services. The basic competing land use model is expanded to include infrastructure development. The extended model leads to the conclusion that due to the dual impact of the infrastructure (lowering the value of ecosystem services and increasing the private rents to developed land), the size of the natural area in the long-term equilibrium will be lower compared to the basic model. The preservation of nature ceases to be profitable enough. Infrastructure also reduces the marginal costs of conversion and thus increasing the volume of natural land being converted at avery moment along the transition path. If the decisions on optimal management of natural areas and infrastructure development are undertaken together, the result is a lower density of the infrastructure network and a larger ecosystem area in the steady state.

The paper investigates the possibility of utilisation of heat-recirculating systems for fuel conversions having low net thermal effect. The experimental part is conducted with an electrically heated heat exchanger. It is shown that heat-recirculating systems can operate under superadiabatic conditions. Their thermal characteristics are provided by means of the dependencies of heat recirculation ratio on process parameters. Further, the heat-recirculating catalytic combustion system is characterised via combustion bifurcation diagrams. The similarities and differences of both those heat-recirculating systems are qualitatively compared and explained. Bifurcation characteristics proves to be useful tools in concise description of practical complex heat-recirculating fuel conversion systems in energy generation.

In this paper a two-disc spinning disc reactor for intensified biodiesel synthesis is described and numerically simulated. The reactor consists of two flat discs, located coaxially and parallel to each other with a gap of 0.2 mm between the discs. The upper disc is located on a rotating shaft while the lower disc is stationary. The feed liquids, triglycerides (TG) and methanol are introduced coaxially along the centre line of rotating disc and stationary disc. Fluid hydrodynamics in the reactor for synthesis of biodiesel from TG and methanol in the presence of a sodium hydroxide catalyst are simulated, using convection-diffusion-reaction species transport model by the CFD software ANSYS©Fluent v. 13.0. The effect of the upper disc’s spinning speed is evaluated. The results show that the rotational speed increase causes an increase of TG conversion despite the fact that the residence time decreases. Compared to data obtained from adequate experiments, the model shows a satisfactory agreement.

Although the gas insulated structures have a high degree of reliability, the unavoidable defects are primary reason of their failures. Partial discharge (PD) has been regarded as an effective indication for condition monitoring and diagnosis of gas insulated switchgears (GISs) to ensure their reliable and stable operation. Among various PD detection methods, the ultra-high frequency (UHF) technique has the advantages of on-line motoring and defect classification. In this paper, there are presented 7 types of artificial electrode systems fabricated for simulation of real insulation defects in gas insulated structures. A real-time measurement system was developed to acquire defect patterns in a form of phase-resolve partial discharge (PRPD) intensity graph, using a UHF sensor. Further, the discharge distribution and statistical characteristics were extracted for defect identification using a neural network algorithm. In addition, a conversion experiment was proposed by detecting the PD pulse simultaneously using a non-induction resistor and a UHF sensor. A relationship between the magnitude of UHF signal and the amplitude of apparent charge was established, which was used for evaluation of PD using the UHF sensor.

The aim of the study was to evaluate the influence of different fillers on the chosen functional properties of experimental composites based on typical polymeric matrix, in order to understand the effect of different fillers on their properties and to develop a simple base composite for further investigations with experimental fillers, e.g. with antimicrobial properties. Previous experiments have been usually based on commercially available composites of unknown composition or compilation of monomers, without reinforcing fillers. Scanning electron microscopy was used to investigate the quality of fillers’ dispersion, which was satisfying. Results showed significant differences between materials’ diametral tensile strength (p = 0.0019), compressive strength (p < 0.0001), Vickers micro-hardness (p < 0.0001), flexural modules (p = 0.0018), and the degree of conversion (p < 0.0001), but flexural strength was not significantly different (p = 0.0583). Investigations indicated that no filler type had an especially positive impact on the mechanical properties, but reinforcement effect was achieved by proper compilation of silica nanofiller and variable glass fillers. Nanofiller decreased the degree of conversion.

The aim of the investigation presented in this work was to realise complex calculations of a new, combined water-steam system with peak-load hydrogen turbine to be applied in nuclear units with gas-cooled reactors. The system’s characteristic feature is the presence of two heat sources: a nuclear steam generator; and a hydrogen-oxygen combustion chamber. The main idea is to create a system capable to operate in two modes, with one or two heat sources, which leads to a significant output change. The investigation included also the overall efficiency of conversion of the nuclear energy, assumed the heat needed for producing hydrogen and oxygen comes from such a source. This part of the work included an analysis of the rationality of hydrogen production and utilisation. An additional aim of the research was to determine the optimal solution regarding the system performance and the capability of its technical realisation. The obtained results are promising: the system performance is very high, and its operating parameters are technically realisable in today’s conditions. In addition, it enables an emission-free, dispatchable electricity generation during the daytime demand peak.

Wave motion in pipe bends is much more complicated than that in straight pipes, thereby changing considerably the propagation characteristics of guided waves in pipes with bends. Therefore, a better understanding of how guided waves propagate in pipe bends is essential for inspecting pipelines with bends. The interaction between a pipe bend and the most used non-dispersive torsional mode at low frequency in a small-bore pipe is studied in this paper. Experiments are conducted on a magnetostrictive system, and it is observed that T(0,1) bend reflections and mode conversions from T(0,1) to F(1,1) and F(2,1) occur in the pipe bend. The magnitude of the T(0,1) bend reflections increases with increasing propagation distance and excitation frequency. The amplitude of the mode-converted signals also increases with increasing propagation distance, but it decreases with increasing excitation frequency. Because of their longer bent path, the test signals for a pipe bend with a bending angle of 180X are much more complicated than those for one with a bending angle of 90X. Therefore, it is even more difficult to scan a bent pipe with a large bending angle. The present findings provide some insights into how guided waves behave in pipe bends, and they generalize the application of guided-wave inspection in pipelines.

This work presents a theoretical study for the distribution of nanocomposite structure of plasmonic thin-film solar cells through the absorber layers. It can be reduced the material consumption and the cost of solar cell. Adding nanometallic fillers in the absorber layer has been improved optical, electrical characteristics and efficiency of traditional thin film solar cells (ITO /CdS/PbS/Al and SnO2/CdS/CdTe/Cu) models that using sub micro absorber layer. Also, this paper explains analysis of J-V, P-V and external quantum efficiency characteristics for nanocomposites thin film solar cell performance. Also, this paper presents the effect of increasing the concentration of nanofillers on the absorption, energy band gap and electron-hole generation rate of absorber layers and the effect of volume fraction on the energy conversion efficiency, fill factor, space charge region of the nanocomposites solar cells.

Communication with authorities belongs to a field of research with a long and intensive research tradition. The present paper focuses on the process of understanding in oral institutional communication. It will present some mechanisms by which common understanding is achieved by using different resources. In contrast to the numerous papers dealing with written institutional communication, little work has been carried out on conversations in the administration. Based on Becker-Mrotzek’s (1999, 2001) classification of oral institutional communication into three different types: discourse on con-sultation, objection and application, the present paper focuses on data collection interviews or application discourses (Ger. Datenerhebungsgespräche), which form “the major part of citizen-administration-discourses” (Becker-Mrotzek 1999: 1399). Despite the frequency of these types of discourse, they are the subject of remarkably few studies.