Binary vapour-liquid equilibrium of thymoquinone and carbon dioxide at the isothermal conditions was carried out at temperature 323.15 K and pressures from 6 to 10 MPa. The experimental data were fitted to the Soave-Redlich-Kwong equation of state. Results could be used for selection of process parameters in separation of volatiles from raw oil or for evaluation of existing separation technologies.
Measurements of hydrogen solubility in various nitrobenzene-aniline mixtures were conducted in an autoclave reactor with a stirrer and control of temperature. The solubility of hydrogen was measured at 7 different values of temperature (30 °C, 40 °C, 50 °C, 90 °C, 130 °C, 170 °C, 210 °C, respectively), 3 values of stirrer rotation speed (1200 rpm, 1600 rpm, 2000 rpm, respectively) and a range of pressure of 20 ‒ 30 bar. Moreover, pure aniline, pure nitrobenzene and their mixtures with different concentrations were used. In the next step, values of Henry’s constant were calculated. Based on experimental data a dependence of Henry’s constant on temperature for pure aniline and pure nitrobenzene was proposed. Additionally, for each temperature correlations between Henry’s constant and aniline’s concentration in mixture of nitrobenzene-aniline were found.
A modified emulsion polymerisation synthesis route for preparing highly dispersed cationic polystyrene (PS) nanoparticles is reported. The combined use of 2,2′-azobis[2-(2-imidazolin- 2-yl)propane] di-hydrochloride (VA-044) as the initiator and acetone/water as the solvent medium afforded successful synthesis of cationic PS particles as small as 31 nm in diameter. A formation mechanism for the preparation of PS nanoparticles was proposed, whereby the occurrence of rapid acetone diffusion caused spontaneous rupture of emulsion droplets into smaller droplets. Additionally, acetone helped to reduce the surface tension and increase the solubility of styrene, thus inhibiting aggregation and coagulation among the particles. In contrast, VA-044 initiator could effectively regulate the stability of the PS nanoparticles including both the surface charge and size. Other reaction parameters i.e. VA-044 concentration and reaction time were examined to establish the optimum polymerisation conditions.
This paper presents the results of a fi eld study on using mineral materials (fine-grained sand and medium-grained gravel) to reduce the concentration of readily soluble salts in a roadside environment. The investigated soils were Rendzic Sceletic Leptosols from an urban area characterized by a shallow humus horizon with a high content of skeletal parts, as well as a lack of homogeneity of the material in the soil profile. All soil samples were taken from five plots located along the main streets in the city of Opole (Southern Poland). It was revealed that the use of fine-grained sand and medium-grained gravel improved the structure of the surface soil layer, and thus favoured the migration of Na+ and Cl- ions into the soil profile. In comparison to control surfaces readily soluble salts were reduced with gravel and sand application. Furthermore, the mineral materials introduced on the soil surface for salinity neutralization did not affect the quality of the tested roadside calcareous soils. The results indicate that the use of mineral materials reduces soil salinity caused by NaCl. They also show the need to find new methods of salt neutralization, especially of roadside soils in order to improve and protect the quality of the environment.
It has been shown that the precipitation of bismuth orthovanadate from a fly ash leachate is a promising method of vanadium recovery. BiVO4 obtained after appropriate heat treatment can be sold as a pigment. The yield of recovery of solubilised vanadium is equal to 68% and the precipitate is free from nickel impurity. The precipitate is insoluble in the solutions with pH ≥ 3. In more acidic media the solubility of precipitate increases with the decreasing pH. The solubility of the precipitate increases also with the increasing concentration of chloride ions.
The Bulletin of the Polish Academy of Sciences: Technical Sciences (Bull.Pol. Ac.: Tech.) is published bimonthly by the Division IV Engineering Sciences of the Polish Academy of Sciences, since the beginning of the existence of the PAS in 1952. The journal is peer‐reviewed and is published both in printed and electronic form. It is established for the publication of original high quality papers from multidisciplinary Engineering sciences with the following topics preferred: Artificial and Computational Intelligence, Biomedical Engineering and Biotechnology, Civil Engineering, Control, Informatics and Robotics, Electronics, Telecommunication and Optoelectronics, Mechanical and Aeronautical Engineering, Thermodynamics, Material Science and Nanotechnology, Power Systems and Power Electronics.
Journal Metrics: JCR Impact Factor 2018: 1.361, 5 Year Impact Factor: 1.323, SCImago Journal Rank (SJR) 2017: 0.319, Source Normalized Impact per Paper (SNIP) 2017: 1.005, CiteScore 2017: 1.27, The Polish Ministry of Science and Higher Education 2017: 25 points.
Abbreviations/Acronym: Journal citation: Bull. Pol. Ac.: Tech., ISO: Bull. Pol. Acad. Sci.-Tech. Sci., JCR Abbrev: B POL ACAD SCI-TECH Acronym in the Editorial System: BPASTS.
The aim of this study was to determine the solubility of CO2 in perfluorodecalin (PFD) which is frequently used as efficient liquid carrier of respiratory gases in bioprocess engineering. The application of perfluorinated liquid in a microsystem has been presented. Gas-liquid mass transfer during Taylor (slug) flow in a microchannel of circular cross section 0.4 mm in diameter has been investigated. A physicochemical system of the absorption of CO2 from the CO2/N2 mixture in perfluorodecalin has been applied. The Henry’s law constants have been found according to two theoretical approaches: physical (H = 1.22·10-3 mol/m3Pa) or chemical (H = 1.26·10-3 mol/m3Pa) absorption. We are hypothesising that the gas-liquid microchannel system is applicable to determine the solubility of respiratory gases in perfluorinated liquids.
Liquid forging alias squeeze casting gives the combined advantage of casting and forging. Optimum process parameters are important to get a cost-efficient process. In this study, four materials have been identified, which are extensively used in industries. These materials are commercially pure Al and three Al-alloys namely, 2124, 2218 and 6063. The pouring temperature and the mold temperature is maintained at 700oC and 250oC respectively. The materials were developed at seven pressure variations from 0 to 150 MPa. The effect of the pressure on the microstructures, porosity, and hardness has been reported. The coefficient of solubility is estimated for all materials and a polynomial relationship is found to be the best fit with the applied pressure. The pressure of 100 MPa gives better increment in hardness. The melting point and the freezing coefficient of the materials under study have been determined. A linear relationship between the pressure and the freezing time is deduced. It is observed that the solubility and the freezing coefficients depend on the pressure as well, in addition to the composition and temperature.
Using High Performance Liquid Chromatography, concentrations of uric acid in the surface waters of two non-glaciated catchments (Fugle and Dynamisk) on Spitsbergen were measured. Measurements of specific conductivity enabled us to perform tests on the dissolution of the carbonate rocks present in both catchments in both natural and aqueous solutions of uric acid. Samples of calcium urate were made and its water solubility determined. Given a knowledge of concentrations of uric acid, calcium ions and calcium urate solubility product, an estimate of the role of uric acid in the dissolution of carbonate rocks was possible. Uric acid increases the dissolution of carbonate rocks by c. 12.5% in case of the Fugle catchment and 7% in Dynamisk.
Fully synthetic, biochemically inert and water-immiscible liquid perfluorochemicals (PFCs) are recognised as flexible liquid carriers/scavengers of gaseous compounds (respiratory gases mainly, i.e. O2 and CO2) and increasingly applied in bioprocess engineering. A range of unmatched physicochemical properties of liquid PFCs, i.e. outstanding chemo- and thermostability, extremely low surface tension, simultaneous hydro- and lipophobicity, which result from carbon chain substitution with fluorine atoms (the most electronegative chemical element) and the presence of intramolecular C-F bonds (the strongest single bond known in organic chemistry) have been described in detail. Exceptional propensity to solubility of respiratory gases in liquid perfluorinated compounds has been widely discussed. Advantages and disadvantages of bioprocess applications of liquid PFCs in the form of a pure PFC as well as in an emulsified form have been pointed out. A liquid PFC-mediated mass transfer intensification in various types of microbial, plant cell and animal cell culture systems: from miniaturised microlitre-scale cultures, via biomaterial-based scaffolds containing culture systems, to litre-scale bioreactors, has been reviewed and elaborated on bearing in mind the benefits of bioprocesses.
Thermodynamic principles for the dissolution of gases in ionic liquids (ILs) and the COSMO-SAC model are presented. Extensive experimental data of Henry’s law constants for CO2, N2 and O2 in ionic liquids at temperatures of 280-363 K are compared with numerical predictions to evaluate the accuracy of the COSMO-SAC model. It is found that Henry’s law constants for CO2 are predicted with an average relative deviation of 13%. Both numerical predictions and experimental data reveal that the solubility of carbon dioxide in ILs increases with an increase in the molar mass of ionic liquids, and is visibly more affected by the anion than by the cation. The calculations also show that the highest solubilities are obtained for [Tf2N]ˉ. Thus, the model can be regarded as a useful tool for the screening of ILs that offer the most favourable CO2 solubilities. The predictions of the COSMOSAC model for N2 and O2 in ILs differ from the pertinent experimental data. In its present form the COSMO-SAC model is not suitable for the estimation of N2 and O2 solubilities in ionic liquids.
The main goal of the present study was to examine the operating characteristics and mechanisms of membrane fouling in integrated membrane bioreactors (IMBRs) at diff erent temperatures. Two IMBRs, each with identical dimensions and confi gurations, were used in the study using synthetic domestic sewage at a low temperature (10°C) and high temperature (25°C). The results indicated that the removal effi ciency of chemical oxygen demand reached 93–96%, but the membrane contribution rate of IMBR2 (10°C) was higher than that of IMBR1 (25°C). The separation burden of the membrane on organic compounds increased at low temperature, which may have sped up the rate of membrane biofouling. The absolute rate of trans-membrane pressure build-up was faster at low temperature, leading to shorter IMBR operating times. Soluble microbial products (SMPs) and extracellular polymeric substances (EPSs) in the IMBRs signifi cantly increased at low temperature. These substances intensifi ed defl occulation, with an accompanying reduction of fl oc size and the release of EPSs at low temperature, which facilitated the formation of cake foulants on the surface, covering the entire membrane area. The protein and polysaccharide concentrations of SMPs and EPSs in the IMBRs were correlated with the concentration of C8-HSL. It was demonstrated that temperature aff ected the concentration of C8-HSL, which controlled the excretion of EPSs and SMPs and thus the membrane biofouling process.