This paper addresses the tensile and flexural strength of HPC (high performance concrete). The aim of the paper is to analyse the efficiency of models proposed in different codes. In particular, three design procedures from: the ACI 318 [1], Eurocode 2 [2] and the Model Code 2010 [3] are considered. The associations between design tensile strength of concrete obtained from these three codes and compressive strength are compared with experimental results of tensile strength and flexural strength by statistical tools. Experimental results of tensile strength were obtained in the splitting test. Based on this comparison, conclusions are drawn according to the fit between the design methods and the test data. The comparison shows that tensile strength and flexural strength of HPC depend on more influential factors and not only compressive strength.

This article deals with the problem of determining the resistance of end-plate connections. A nonlinear FEM model of the joint was constructed in order to predict its carrying capacity. A standard code procedure was done as well. The analyses have been done to assess atypical end-plate joints designed and constructed as a part of roof structures.

Steel Mesh-Reinforced Cementitious Composites (SMRCC) (traditionally known as ferrocement) have been in existence for few decades, but have some limitations set on element thickness and number of reinforcing mesh layers and the resulting deflection ductility. Therefore, the author has made an attempt to explore whether deflection ductility will improve in mesh-reinforced cementitious composites (25 mm thick) if discontinuous fibres are added to slab elements. For this purpose, thin slab elements of dimensions 700 mm (length) × 200 mm (width) × 25 mm (thickness) were cast and subjected to four point bending tests. Based on the flexural tests conducted on SMRCC (Control Slab Elements, cast with Steel Mesh Volume of reinforcement, MVr = 0.78, 0.94, and 1.23%) and Hybrid Mesh-and-Fibre-Reinforced Cement Based Composite (HMFRCBC) (Test Slab Elements, combining MVr = 0.78, 0.94 and 1.23% and Polyolefin Fibre Volume fraction, PO-FVf = 0.5‒2.5% of volume of specimens, with 0.5% interval), load-deflection and the deflection ductility index were analyzed. From the flexural load-deflection curves it has been observed that HMFRCBC slabs demonstrate higher flexural load-carrying capacity and deflection ductility when compared to SMRCC slabs. This study shows that higher the polyolefin fibre volume fraction (PO-FVf) from 0.5 to 2.5% (with a 0.5% interval) in HMFRCBC slabs, the higher the flexural deflection ductility. The Deflection Ductility Index (DDI) of HMFRCBC (with 5 layers of mesh and PO-FVf = 2.5%) is 4.5 times that of SMRCC. This study recommends that HMFRCBC can be used as an innovative construction material due to its higher flexural ductility characteristics.

Assessment of the flexural buckling resistance of bisymmetrical I-section beam-columns using FEM is widely discussed in the paper with regard to their imperfect model. The concept of equivalent geometric imperfections is applied in compliance with the so-called Eurocode’s general method. Various imperfection profiles are considered. The global effect of imperfections on the real compression members behaviour is illustrated by the comparison of imperfect beam-columns resistance and the resistance of their perfect counterparts. Numerous FEM simulations with regard to the stability behaviour of laterally and torsionally restrained steel structural elements of hot-rolled wide flange HEB section subjected to both compression and bending about the major or minor principal axes were performed. Geometrically and materially nonlinear analyses, GMNA for perfect structural elements and GMNIA for imperfect ones, preceded by LBA for the initial curvature evaluation of imperfect member configuration prior to loading were carried out. Numerical modelling and simulations were conducted with use of ABAQUS/Standard program. FEM results are compared with those obtained using the Eurocode’s interaction criteria of Method 1 and 2. Concluding remarks with regard to a necessity of equivalent imperfection profiles inclusion in modelling of the in-plane resistance of compression members are presented.

This study focuses to develop a new hybrid Engineered Cementitious Composite (ECC) and assesses the performance of a new hybrid ECC based on the steel short random fiber reinforcement. This hybrid ECC aims to improve the tensile strength of cementitious material and enhance better flexural performance in an RC beam. In this study, four different mixes have been investigated. ECC with Poly Vinyl Alcohol (PVA) fiber and PolyPropylene (PP) fiber of 2.0% volume fraction are the two Mono fiber mixes; ECC mix with PVA fiber of 0.65% volume fraction hybridized with steel fiber of 1.35% volume fraction, PP fiber of 0.65% volume fraction hybridized with steel of 1.35% volume fraction are the two additional different hybrid mixes. The material properties of mono fiber ECC with 2.0 % of PVA is kept as the reference mix in this study. The hybridization with fibers has a notable achievement on the uniaxial tensile strength, compressive strength, Young’s modulus, and flexural behavior in ECC layered RC beams. From the results, it has been observed that the mix with PVA fiber of 0.65% volume fraction hybrid with steel fiber of 1.35% volume fraction exhibitimprovements in tensile strength, flexural strength, andenergy absorption. ThePP fiber of 0.65% volume fraction hybridized with steel of 1.35% volume fraction mix has reasonable flexural performance and notable achievement in displacement ductility overthe reference mix.