This paper addresses weighted L2 gain performance switching controller design of discrete-time switched linear systems with average dwell time (ADT) scheme. Two kinds of methods, so called linearizing change-of-variables based method and controller variable elimination method, are considered for the output-feedback control with a supervisor enforcing a reset rule at each switching instant are considered respectively. Furthermore, some comparison between these two methods are also given.
When the distribution of water quality samples is roughly balanced, the Bayesian criterion model of water-inrush source generally can obtain relatively accurate results of water-inrush source identification. However, it is often difficult to achieve desired classification results when training samples are imbalanced. Sample imbalance is common in the source identification of mine water-inrush. Therefore, we propose a three-dimensional (3D) spatial resampling method based on rare water quality samples, which achieves the balance of water quality samples. Based on the virtual water sample points distributed by the 3D grid, the method uses the 3D Inverse Distance Weighting (IDW) method to interpolate the groundwater ion concentration of the virtual water samples to achieve oversampling of rare water samples. Case study in Gubei Coal Mine shows that the method improves overall discriminant accuracy of the Bayesian criterion model by 5.26%, from 85.26% to 90.69%. In particular, the discriminative precision of the rare class is improved from 0% to 83.33%, which indicates that the method can improve the discriminant accuracy of the rare class to large extent. In addition, this method increases the Kappa coefficient of the model by 19.92%, from 52.26% to 72.19%, increasing the degree of consistency from “general” to “significant”. Our research is of significance to enriching and improving the theory of prevention and treatment of mine water damage.
In this paper, a new set of intuitionistic fuzzy aggregation operators have been introduced under the environment of intuitionistic fuzzy sets (IFSs). For this, firstly focused on some existing aggregation operators and then new operational rules known as Dombi operation have been pro- posed which make the advancement of flexibility behavior with the parameter. Based on Dombi operation laws, some new averaging and geometric aggregation operators namely, intuitionistic fuzzy Dombi weighted averaging, ordered weighted averaging and hybrid weighted averaging operator, classified as IFDWA, IFDOWA and IFDHWA operators respectively and intuitionistic fuzzy Dombi geometric, ordered weighted geometric and hybrid weighted geometric operators, labeled as IFDWG, IFDOWG and IFDHWG operators respectively have been proposed. Further, some properties such as idempotency, boundedness, monotonicity and commutative are investigated. Finally, a multi-attribute decision-making model has been developed for the proposed operators to select the best mutual fund for investment. The execution of the comparative study has been examined with the existing operators in this environment.
The paper aims at the higher reactive power management complexity caused by the access of distributed power, and the problem such as large data exchange capacity, low accuracy of reactive power distribution, a slow convergence rate, and so on, may appear when the controlled objects are large. This paper proposes a reactive power and voltage control management strategy based on virtual reactance cloud control. The coupling between active power and reactive power in the system is effectively eliminated through the virtual reactance. At the same time, huge amounts of data are treated to parallel processing by using the cloud computing model parallel distributed processing, realize the uncertainty transformation between qualitative concept and quantitative value. The power distribution matrix is formed according to graph theory, and the accurate allocation of reactive power is realized by applying the cloud control model. Finally, the validity and rationality of this method are verified by testing a practical node system through simulation.
Bovine parvovirus (BPV), bovine coronavirus (BCoV) and bovine parainfluenza virus (BPIV) are common etiologies causing gastrointestinal and respiratory diseases in dairy herds. However, there are few reports on the synchronous detection of BPV, BCoV and BPIV. The present article aimed to develop a quick and accurate RT-PCR assay to synchronously detect BPV, BCoV and BPIV based on their specific probes. One pair universal primers, one pair specific primers and one specific probe was designed and synthesized. After the concentrations of primer and probe and annealing temperature were strictly optimized, the specificity, sensitivity and repeatability of the established triplex probe qRT-PCR were evaluated, respectively. The results showed the recombinant plasmids of pMD18-T-BPV, pMD18-T-BCoV and pMD18-T-BPIV were 554bp, 699bp and 704bp, respectively. The optimal annealing temperature was set at 45.0°C for triplex qRT-PCR. The triplex probe qRT-PCR can only synchronously detect BPV, BCoV and BPIV. Detection sensitivities were 2.0×102, 2.0×102 and 2.0×101 copies/μL for BPV, BCoV and BPIV, being 1000-fold greater than that in the conventional PCR. Detection of clinical samples demon- strated that triplex probe qRT-PCR had a higher sensitivity and specificity. The intra-assay and inter-assay coefficient of variation were lower than 2.0%. Clinical specimens verified that the triplex qRT-PCR had a higher sensitivity and specificity than universal PCR. In conclusion, this triplex probe qRT-PCR could detect only BPV, BCoV and BPIV. Minimum detection limits were 2.0×102 copies/μL for BPV and BCoV, and 2.0×101 copies/μL for BPIV. The sensitivity of this triplex probe qRT-PCR was 1000-fold greater than that in the conventional PCR. The newly qRT-PCR could be used to monitor or differentially diagnose virus infection.
In multi-axis motion control systems, the tracking errors of single axis load and the contour errors caused by the mismatch of dynamic characteristics between the moving axes will affect the accuracy of the motion control system. To solve this issue, a biaxial motion control strategy based on double-iterative learning and cross-coupling control is proposed. The proposed control method improves the accuracy of the motion control system by improving individual axis tracking performance and contour tracking performance. On this basis, a rapid control prototype (RCP) is designed, and the experiment is verified by the hardware and software platforms, LabVIEW and Compact RIO. The whole design shows enhancement in the precision of the motion control of the multiaxis system. The performance in individual axis tracking and contour tracking is greatly improved.
The sodium expansion and creep strain of semi-graphitic cathodes are investigated using a modified Rapoport apparatus. To further understanding of the sodium and bath penetration damage processes, the impact of external stress fluence on the carbon cathode microstructure has been defined with XRD analysis, Raman spectroscopy and scanning electron microscope (SEM). Graphite atoms fracture into smaller fragments that are less directional than the pristine platelets, which allows for a possible filling of the cracks that thus develop by the sodium and bath during aluminum electrolysis. The average microcrystalline size (calculated by Raman spectroscopy) is reduced by the deformation. The decreased intensity and widened ‘G’ and ‘D’ peaks in the analysis indicate the poor order of the sheets along the stacking direction while the consistent layered graphite structure is sustained.
To overcome the detrimental influence of α impulse noise in power line communication and the trap of scarce prior information in traditional noise suppression schemes , a power iteration based fast independent component analysis (PowerICA) based noise suppression scheme is designed in this paper. Firstly, the pseudo-observation signal is constructed by weighted processing so that single-channel blind separation model is transformed into the multi-channel observed model. Then the proposed blind separation algorithm is used to separate noise and source signals. Finally, the effectiveness of the proposed algorithm is verified by experiment simulation. Experiment results show that the proposed algorithm has better separation effect, more stable separation and less implementation time than that of FastICA algorithm, which also improves the real-time performance of communication signal processing.
Finding effective ways to efficiently drive roadways at depths over 1 km has become a hotspot research issue in the field of mining engineering. In this study, based on the local geological conditions in the Xinwen Mining Area (XMA) of China, in-situ stress measurements were conducted in 15 representative deep roadways, which revealed the overall tectonic stress field pattern, with the domination of the horizontal principal stresses. The latter values reached as high as 42.19 MPa, posing a significant challenge to the drivage work. Given this, a comprehensive set of innovative techniques for efficiently driving roadways at depths over 1 km was developed, including (i) controlled blasting with bidirectional energy focusing for directional fracturing, (ii) controlled blasting with multidirectional energy distribution for efficient rock fragmentation, (iii) wedge-cylinder duplex cuts centered on double empty holes, and (iv) high-strength supports for deep roadways. The proposed set of techniques was successfully implemented in the –1010 west rock roadway (WRR) drivage at the Huafeng Coal Mine (HCM). The improved drivage efficiency was characterized by the average and maximum monthly advances of 125 and 151 m, respectively. The roadway cross-sectional shape accuracy was also significantly improved, with the overbreak and underbreak zones being less than 50 mm. The deformation in the surrounding rock of roadway (SRR) was adequately controlled, thus avoiding repeated maintenance and repair. The relevant research results can provide technical guidance for efficient drivage of roadways at depths over 1 km in other mining areas in China and worldwide.
With the rise of coal mine underground reservoir engineering in the Shendong Mining Area, the space time dynamic evolution prediction of storage coefficient is becoming one of the critical technical problems for long-term reservoir operation. This coefficient directly determines the storage capacity and the comprehensive benefits of the operation of a coal mine underground reservoir. To this end, the proposed underground reservoir in Daliuta coal mine (No. 22616 working face) is selected in this study for the development and application of an experimental device to measure the storage coefficient. Rock and coal fragments from similar materials are prepared, which are filled and loaded according to the caving rock nature as well as the lumpiness and accumulation mode characteristics pertaining to No. 22616 working face. Subsequently, the measured storage coefficient under circulating water injection conditions revealed a four-dimensional spatial and temporal pattern. It followed the law of storage coefficient under joint interaction of water-rock and stress. The results showed that, prior to the experiment, rock and coal fragments made from similar materials had good water resistance when the paraffin content was set at 8%. The three stress zones were defined based on a theoretical analysis, which were applied on the corresponding loads. During the experiments, significant regional differences were found in the top surface with persisting subsidence of each stress loading zone. Hence, compared with its initial state, the maximum subsidence in the stress stability zone, the stress recovery zone, and the low-stress zone was 7.89, 5.8, and 1.83 mm, respectively. While the storage capacity and the storage coefficient gradually decreased, the former ranged from 0.2429 to 0.2397 m3, and the latter ranged from 0.270 to 0.266. The experimental results are verified by drainage engineering tests in the Shendong Mining Area. In essence, the storage coefficient had remarkable spatial distribution characteristics and a time-varying effect. In space, the storage coefficient increased with height along the vertical direction of the coal mine underground reservoir. However, it decreased with the distance from the boundary of the dam body in the horizontal direction. With time, the storage coefficient decreased dynamically. This study provides a new way of predicting the storage coefficient of a coal mine underground reservoir.
Wet shotcrete technology is being gradually used in roadway support in frigid mining areas. Thus, problems such as low strength, fragility, and high repair rate have also emerged. This study focuses on low strength, cracking, and other problems in the wet shotcrete support of a mine. It introduced the fishbone diagram to investigate the effects of temperature, cement content, and water-cement ratio (W/C) on the strength of the shotcrete layer. The microscopic morphology of wet shotcrete based on scanning electron microscopy (SEM) is observed. Results demonstrated that temperature was the main influencing factor of wet shotcrete in frigid mining areas. When the curing temperature was lower than 10°C, the early strength of wet shotcrete dropped significantly. Temperatures above 15°C were favorable for later gain in strength. W/C was of a complementary relationship with strength development at different ages. Temperature was the essential factor that influenced the microscopic morphology of wet shotcrete. Furthermore, internal initial porosity and aggregate interface bonding strength had a direct effect on macro-mechanical properties of wet shotcrete.
Significant differences in the physical and mechanical properties exist between the rock masses on two sides of an ore-rock contact zone, which the production tunnels of an underground mine must pass through. Compared with a single rock mass, the mechanical behavior of the contact zone composite rock comprising two types of rock is more complex. In order to predict the overall strength of the composite rock with different contact angles, iron ore-marble composite rock sample uniaxial compression tests were conducted. The results showed that composite rock samples with different contact angles failed in two different modes under compression. The strengths of the composite rock samples were lower than those of both the pure iron ore samples and pure marble samples, and were also related to the contact angle. According to the stress-strain relationship of the contact surface in the composite rock sample, there were constraint stresses on the contact surface between the two types of rock medium in the composite rock samples. This stress state could reveal the effect of the constraint stress in the composite rock samples with different contact angles on their strengths. Based on the Mohr-Coulomb criterion, a strength model of the composite rock considering the constraint stress on the contact surface was constructed, which could provide a theoretical basis for stability researches and designs of contact zone tunnels.