For building applications, woven fabrics have been widely used as finishing elements of room interior but not in particular aimed for sound absorbers. Considering the micro perforation of the woven fabrics, they should have potential to be used as micro-perforated panel (MPP) absorbers; some measurement results indicated such absorption ability. Hence, it is of importance to have a sound absorption model of the woven fabrics to enable us predicting their sound absorption characteristic that is beneficial in engineering design phase. Treating the woven fabric as a rigid frame, a fluid equivalent model is employed based on the formulation of Johnson-Champoux-Allard (JCA). The model obtained is then validated by measurement results where three kinds of commercially available woven fabrics are evaluated by considering their perforation properties. It is found that the model can reasonably predict their sound absorption coefficients. However, the presence of perturbations in pores give rise to inaccuracy of resistive component of the predicted surface impedance. The use of measured static flow resistive and corrected viscous length in the calculations are useful to cope with such a situation. Otherwise, the use of an optimized simple model as a function of flow resistivity is also applicable for this case.

Telomeres are repetitive sequence structures at the ends of chromosomes. They consist of the double stranded DNA repeats followed by the short single stranded DNA. In humans and other verterbrates the telomeric sequence is composed of tandem of TTAGGG repeats. With each cells division telomeres shorten by up to 200 base pairs. Telomerase is an enzyme responsible for continuous cell growth and is repressed in most somatic cells, except proliferating progenitor cells, but in more than 85% of cancer cells telomerase expression is observed. Tumour cells with metastatic potential may demonstrate a high telomerase activity, allowing cells to escape from the inhibition of cell proliferation due to shortened telomeres. Determination of telomerase expres- sion was performed with the use of PCR ELISA in samples isolated from bovine leukaemia virus (BLV) infected cows. Telomerase activity was found in almost all investigated samples. The relative telomerase activity (RTA) was higher in infected cows than in healthy animals and the differences were statistically significant (α=0.05). In blood lymphocytes of BLV-infected cows the mean values of telomerase expression determined in real-time PCR were 3534.12 copies, in the healthy group there were 1010.10 copies and these differences were also statistically significant. For telomere length evaluation the Telomere PNA/FITC FISH and Telomere PNA/FITC FISH for flow cytometry were used. The mean fluorescence intensity of telomere sequences calculated on the surface of interphase nuclei of leukaemic blood lymphocytes was lower than that in the control animals and the difference was statistically significant. The mean length of telomeres in BLV- infected and healthy cows was 31.63 ± 12.62 and 38.4 ± 4.03, (p=0.112), respectively.

Dendritic cells (DCs) due to their ability to present antigens are essential during the immune response to infections. The aim of the study was to evaluate the influence of bovine leukaemia virus (BLV) infection on DC properties. Cytokine profiles of myeloid, plasmacytoid and mono- cyte derived DCs from BLV infected cattle were analysed. Concentrations of IL-6, IL-10, IL-12, IFN-γ, and TNF-α in DC cultures were measured by flow cytometry. Obtained results indicated activation of pDCs population, where a significant increase in production of the IFN-γ was shown. Meanwhile, a decrease in production of IFN-γ and increase in production of IL-10 were shown in mDCs; the main population responsible for antigens presentation. This may indicate a contribu- tory role of the population during the process of persistent infection. In MoDCs population a significant elevation in secretion of proinflammatory cytokines – IL-6 and TNF-α was noted.

Natural fibres are attractive as the raw material for developing sound absorber, as they are green, eco-friendly, and health friendly. In this paper, pineapple leaf fibre/epoxy composite is considered in sound absorber development where several values of mechanical pressures were introduced during the fabrication of absorber composite. The results show that the composite can absorb incoming sound wave, where sound absorption coefficients α _n > 0.5 are pronounced at mid and high frequencies. It is also found that 23.15 kN/m^2 mechanical pressure in composite fabrication is preferred, while higher pressure leads to solid panel rather than sound absorber so that the absorption capability reduces. To extend the absorption towards lower frequency, the composite absorber requires thickness higher than 3 cm, while a thinner absorber is only effective at 1 kHz and above. Additionally, it is confirmed that the Delany-Bazley formulation fails to predict associated absorption behavior of pineapple leaf fibre-based absorber. Meanwhile, a modified Delany-Bazley model discussed in this paper is more useful. It is expected that the model can assist further development of the pineapple leaf composite sound absorber.

The present review is mainly focused on the extended analysis of the results obtained from coupled measurement techniques of a thermal imaging camera and chronoamperometry for imines in undoped and doped states. This coupled technique allows to identify the current-voltage characteristics of thin films based on imine, as well as to assess layer defects in thermal images. Additional analysis of results provides further information regarding sample parameters, such as resistance, conductivity, thermal resistance, and Joule power heat correlated with increasing temperature. As can be concluded from this review, it is possible not only to study material properties at the supramolecular level, but also to tune macroscopic properties of -conjugated systems. A detailed study of the structure-thermoelectrical properties in a series of eight unsymmetrical and symmetrical imines for the field of optoelectronics and photovoltaics has been undertaken. Apart from this molecular engineering, the imines properties were also tuned by supramolecular engineering via protonation with camphorsulfonic acid and by creation of bulk-heterojunction compositions based on poly(4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl-alt-3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophene-4,6-diyl) and/or [6,6]-phenyl-C71-butyric acid methyl ester, poly(3,4-ethylenedioxythiophene) towards the analysed donor or acceptor ability of imines in the active layer. The use of coupled measurement techniques of a thermal imaging camera and chronoamperometry allows obtaining comprehensive data on thermoelectric properties and defects indicating possible molecule rearrangement within the layer.

In this work, two thermal- and air-stable, hole transporting materials (HTM) in perovskite solar cells are analyzed. Those obtained and investigated materials were two polyazomethines: the first one with three thiophene rings and 3,3′-dimethoxybenzidine moieties (S9) and the second one with three thiophene rings and fluorene moieties (S7). Furthermore, presented polyazomethines were characterized by Fourier transform infrared spectroscopy (FTIR), UV–vis spectroscopy, atomic force microscopy (AFM) and thermogravimetric analysis (TGA) experiments. Both polyazomethines (S7 and S9) possessed good thermal stability with a 5% weight loss at 406 and 377°C, respectively. The conductivity of S7 was two orders of magnitude higher than for S9 polymer (2.7 × 10⁻⁸ S/cm, and 2.6 × 10⁻¹⁰ S/cm, respectively). Moreover, polyazomethine S9 exhibited 31 nm bathochromic shift of the absorption band maximum compared to S7.

Obtained perovskite was investigated by UV–vis and XRD. Electrical parameters of perovskite solar cells (PSC) were investigated at Standard Test Conditions (STC). It was found that both polyazomethines protect perovskite which is confirmed by ageing test where Voc did not decrease significantly for solar cells with HTM in contrast to solar cell without hole conductor, where V_oc decrease was substantial. The best photoconversion efficiency (PCE = 6.9%), among two investigated in this work polyazomethines, was obtained for device with the following architectures FTO/TiO₂/TiO₂ + perovskite/S7/Au. Stability test proved the procreative effects of polyazomethines on perovskite absorber.

Electricity storage is one of the best-known methods of balancing the energy supply and demand at a given moment. The article presents an innovative solution for the construction of an electric energy storage device obtained from an innovative photovoltaic panel made of new dye-based photovoltaic modules and newly developed supercapacitors – which can be used as an emergency power source. In the paper, for the first time, we focused on the successful paring of new dye-sensitized solar cell (DSSC) with novel supercapacitors. In the first step, a microprocessor stand was constructed using Artificial Intelligence algorithms to control the parameters of the environment, as well as the solar charger composed of six DSSC cells with the dimensions of 100_100 mm and 126 CR2032 coin cells with a total capacitance of 60 F containing redox-active aqueous electrolyte. It was proven that the solar charger store enough energy to power, i.e. SOS transmitter or igniters, using a 5 V signal.