Some studies show that cells are able to penetrate through pores that are smaller than cell size. It concerns especially Red Blood Cells but it also may concern different types of biological cells. Such penetration of small pores is a very significant problem in the filtration process, for example in micro- or ultrafiltration. Deformability of cells allows them to go through the porous membrane and contaminate permeate. This paper shows how cells can penetrate small cylindrical holes and tries to assess mechanical stress in a cell during this process. A new mathematical approach to this phenomenon was presented, based on assumptions that were made during the microscopic observation of Red Blood Cell aspiration into a small capillary. The computational model concerns Red Blood Cell geometry. The mathematical model allows to obtain geometrical relation as well as mechanical stress relations.

This article presents a critical mini-review of research conducted on bioelectrochemical reactors with emphasis placed on microbial fuel cells (MFC) and microbial electrolysis cells (MEC). The principle of operation and typical constructions of MFCs and MECs were presented. The types of anodes and cathodes, ion-selective membranes and microorganisms used were discussed along with their limitations.

Photovoltaic cells have been used for a long time to supply the electrical devices of small power in areas without access to the electricity networks (or other sources of electric energy). The ecological aspect of the use of the renewable energy sources, together with the technology development and increasingly lower costs of production the photovoltaic cells, cause the increase of their application. The solar power plants are built in several places in the world, not necessarily in the areas of high light intensity. Nowadays, such developments mostly depend on the wealth of a particular country. The largest photovoltaic power stations have power of a several dozen of MW. The major disadvantage of the photovoltaic cells is that the energy production is possible only during the day. This causes a necessity of energy accumulation in large photovoltaic systems. One possibility of storing large amounts of energy gives a hydrogen fuel, generated in the electrolysers powered directly from photovoltaic cells. Hydrogen, stored in pressure tanks or in tanks with synthetic porous materials, can be again used to produce electricity in fuel cells. This paper introduces selected issues and test results associated with the use of photovoltaic cells to power the hydrogen generators. The possible connections of photovoltaic modules integrated with electrolysers were analyzed. In this article the results of the electricity daily production by polycrystalline photovoltaic cells, collected in the course of the entire year were also presented.

The direct carbon fuel cell technology provides excellent conditions for conversion of chemical energy of carbon-containing solid fuels directly into electricity. The technology is very promising since it is relatively simple compared to other fuel cell technologies and accepts all carbon-reach substances as possible fuels. Furthermore, it makes possible to use atmospheric oxygen as the oxidizer. In this paper the results of authors' recent investigations focused on analysis of the performance of a direct carbon fuel cell supplied with graphite, granulated carbonized biomass (biocarbon), and granulated hard coal are presented. The comparison of the voltage-current characteristics indicated that the results obtained for the case when the cell was operated with carbonized biomass and hard coal were much more promising than those obtained for graphite. The effects of fuel type and the surface area of the cathode on operation performance of the fuel cell were also discussed.

The paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles in the form of semi-sinusoidal and trapezoidal signals was investigated. The load was provided with the aid of an in-house-developed electronic load unit, which was fully PC controlled. The apparatus was commissioned by testing the steady-state operation of the module. The obtained efficiency of the fuel cell shows that the test apparatus used in the study provides data in substantial agreement with the manufacturer’s data.

The application of modern scientific methods and measuring techniques can extend the empirical knowledge used for centuries by violinmakers for making and adjusting the sound of violins, violas, and cellos.

Accessories such as strings and tailpieces have been studied recently with respect to style and historical coherence, after having been somehow neglected by researchers in the past. These fittings have played an important part in the history of these instruments, but have largely disappeared as they have been modernised. However, the mechanics of these accessories contribute significantly to sound production in ways that have changed over time with different musical aesthetics and in different technical contexts. There is a need to further elucidate the function and musical contribution of strings and tailpieces.

With this research we are trying to understand the modifications of the cello's sound as a consequence of tailpiece characteristics (shape of the tailpiece and types of attachments). Modal analysis was used to first investigate the vibration modes of the tailpiece when mounted on a non-reactive rig and then when mounted on a real cello where it can interact with the modes of the instrument's corpus. A preliminary study of the effect of the tailpiece cord length will be presented.

The article presents a zero-dimensional mathematical model of a tubular fuel cell and its verification on four experiments. Despite the fact that fuel cells are still rarely used in commercial applications, their use has become increasingly more common. Computational Flow Mechanics codes allow to predict basic parameters of a cell such as current, voltage, combustion composition, exhaust temperature, etc. Precise models are particularly important for a complex energy system, where fuel cells cooperate with gas, gas-steam cycles or ORCs and their thermodynamic parameters affect those systems. The proposed model employs extended Nernst equation to determine the fuel cell voltage and steadystate shifting reaction equilibrium to calculate the exhaust composition. Additionally, the reaction of methane reforming and the electrochemical reaction of hydrogen and oxygen have been implemented into the model. The numerical simulation results were compared with available experiment results and the differences, with the exception of the Tomlin experiment, are below 5%. It has been proven that the increase in current density lowers the electrical efficiency of SOFCs, hence fuel cells typically work at low current density, with a corresponding efficiency of 45–50% and with a low emission level (zero emissions in case of hydrogen combustion).

Metallic foams are materials of which the research is still on-going, with the broad applicability in many different areas (e.g. automotive

industry, building industry, medicine, etc.). These metallic materials have specific properties, such as large rigidity at low density, high

thermal conductivity, capability to absorb energy, etc. The work is focused on the preparation of these materials using conventional casting

technology (infiltration method), which ensures rapid and economically feasible method for production of shaped components. In the

experimental part we studied conditions of casting of metallic foams with open pores and irregular cell structure made of ferrous and nonferrous

alloys by use of various types of filler material (precursors).

Taking bacterial virulence factors as targets is a new therapy for treating host bacterial infection. The aim of this study was to investigate the effect of matrine on α-hemolysin production of Staphylococcus aureus (S. aureus) and reducing the damage to bovine mammary epithelial cells (BMECs) induced by S. aureus α-hemolysin. Subinhibitory concentrations of matrine decreased the production of α-hemolysin in none dose-dependent manner and matrine exhibited a protective effect on S. aureus-induced BMECs injury. The results indicated that the structure of matrine may potentially be used as a basic structure for development of drugs aimed at curing and preventing dairy bovine mastitis.

Hybryd PLD method was used for deposition high quality thin Ti, TiN, Ti(C,N) and DLC coatings. The kinetic energy of the evaporated particles was controlled by application of variation of different reactive and non reactive atmospheres during deposition. The purpose was to improve adhesion by building a bridge between the real ceramic coating and the substrate. A new layer composition layout was proposed by application of a buffer, starting layer. Advanced HRTEM investigation based on high resolution transmission electron microscopy was used to reveal structure dependence on specific atmosphere in the reactive chamber. New experimental technique to examine the crystallographic orientation based on X-ray texture tomography was applied to estimate contribution of the atmosphere to crystal orientation. Using Dictyostelium discoideum cells as a model organism for specific and nonspecific adhesion, kinetics of shear flow-induced cell detachment was studied. For a given cell, detachment occurs for critical stress values caused by the applied hydrodynamic pressure above a threshold. Cells are then removed from the substrate with an apparent first-order rate reaction that strongly depends on the stress. The threshold stress depends on cell size and physicochemical properties of the substrate, but it is not affected by depolymerization of the actin and tubulin cytoskeleton.

Industrial engineers gather knowledge during their bachelor studies through lectures and

practical classes. The goal of practical class might be an extension of knowledge and/or a

consolidation and application of already gathered knowledge. It is observed that there exists

a gap between theory learnt during lectures and practical classes. If practical classes require

holistic approach and solving complex tasks (problems), students strive with understanding

relations and connections between parts of knowledge. The aim of this article is to show an

example of a simple practical assignment that can serve as a bridge between lectures and

practical classes through discussion of interactions and relations between parts of theoretical

knowledge. It is an example of in-class simulating of a line and cellular layout considering

discussion of elements impacting and impacted by the type of layout (e.g. learning curve,

changeovers, etc.). In-class verification of the presented approach confirmed its usability for

teaching industrial engineers and bridging the gap between theory delivered through lectures

and more advanced practical classes.

Based on mathematical modeling and numerical simulations, applicativity of various biofuels on high temperature fuel cell performance are presented. Governing equations of high temperature fuel cell modeling are given. Adequate simulators of both solid oxide fuel cell (SOFC) and molten carbonate fuel cell (MCFC) have been done and described. Performance of these fuel cells with different biofuels is shown. Some characteristics are given and described. Advantages and disadvantages of various biofuels from the system performance point of view are pointed out. An analysis of various biofuels as potential fuels for SOFC and MCFC is presented. The results are compared with both methane and hydrogen as the reference fuels. The biofuels are characterized by both lower efficiency and lower fuel utilization factors compared with methane. The presented results are based on a 0D mathematical model in the design point calculation. The governing equations of the model are also presented. Technical and financial analysis of high temperature fuel cells (SOFC and MCFC) are shown. High temperature fuel cells can be fed by biofuels like: biogas, bioethanol, and biomethanol. Operational costs and possible incomes of those installation types were estimated and analyzed. A comparison against classic power generation units is shown. A basic indicator net present value (NPV) for projects was estimated and commented.

Cardiac Radiofrequency (RF) ablation is a commonly used clinical procedure for treating many cardiac arrhythmias. However, the efficacy of RF ablation may be limited by two factors: small ventricular lesions and impedance rise, leading to coagulum formation and desiccation of tissue. In this paper, a high frequency (HF) energy ablation system operating at 27.12 MHz based on an automated load matching system was developed. A HF energy matched probe associated to the automated impedance matching device ensures optimal transfer of the energy to the load. The aim of this study was to evaluate this energy for catheter ablation of the atrioventricular junction.

In vivo studies were performed using 10 sheep to characterize the lesions created with the impedance matching system. No cardiac perforation was noted. No thrombus was observed at the catheter tip. Acute lesions ranged from 3 to 45 mm in diameter (mean ±SD = 10.3±10) and from 1 to 15 mm in depth (6.7±3.9), exhibiting a close relationship between HF delivered power level and lesion size. Catheter ablation using HF current is feasible and appears effective in producing a stable AV block when applied at the AV junction and large myocardial lesions at ventricular sites.

Cell culture transplantation is very promising in the treatment of various diseases. Cells obtained from a number of sources have been analysed to provide a basis for further studies in the area of regenerative medicine. The objective of the study was to compare morphological and phenotypic changes in cat adipose tissue and bone marrow cell cultures from the first to fifth passages. Adipose tissue and bone marrow were used to obtain cell cultures (coming from 3 cats) using standard methods with own modification. Phenotype changes were monitored by CD-marker identification and CD pan-keratin. The cytogenetic analysis was performed on 50 metaphase plates of cell cultures from the first to fifth passage. Cytogenetic assays showed that the adipose tissue cell culture (ATCC) at all passages was more stable than the bone marrow cell culture (BMCC).

The subject of the study are alumina foams produced by gelcasting method. The results of micro-computed tomography of the foam samples are used to create the numerical model reconstructing the real structure of the foam skeleton as well as the simplified periodic open-cell structure models. The aim of the paper is to present a new idea of the energy-based assessment of failure strength under uniaxial compression of real alumina foams of various porosity with use of the periodic structure model of the same porosity. Considering two kinds of cellular structures: the periodic one, for instance of fcc type, and the random structure of real alumina foam it is possible to justify the hypothesis, computationally and experimentally, that the same elastic energy density cumulated in the both structures of the same porosity allows to determine the close values of fracture strength under compression. Application of finite element computations for the analysis of deformation and failure processes in real ceramic foams is time consuming. Therefore, the use of simplified periodic cell structure models for the assessment of elastic moduli and failure strength appears very attractive from the point of view of practical applications.

This paper deals with an observer design for a p-cell chopper. The goal is to reduce drastically the number of sensors in such system by using an observer in order to estimate all the capacitor voltages. Furthermore, considering an instantaneous model of a p-cell chopper, an interconnected observer is designed in order to estimate the capacitor voltages. This is realized by using only the load current measurement. Simulation results are given in order to illustrate the performance of such observer. To demonstrate the validity of our approach, experimental results based on Digital Signal Processor (DSP) are presented.

Based on mathematical modelling and numerical simulations, a control strategy for a Molten Carbonate Fuel Cell Hybrid System (MCFC-HS) is presented. Adequate maps of performances with three independent parameters are shown. The independent parameters are as follows: stack current, fuel mass flow and compressor outlet pressure. Those parameters can be controlled by external load, fuel valve and turbine-compressor shaft speed, respectively. The control system is purposed to meet many constraints: e.g. stack temperature, steam-to-carbon ratio, compressor surge limitation, etc. The aim is to achieve maximum efficiency of power generated within these constraints. Governing equations of MCFC-HS modelling are given. An operational line of the MCFC-GT system is presented which fulfils several constraints (temperature difference, cell temperature, etc.) The system is able to achieve efficiency of more than 62% even in part-load operation.

The measured rate of release of intercellular protein from yeast cells by ultrasonication was applied for evaluating the effects of sonication reactor geometry on cell disruption rate and for validation of the simulation method. Disintegration of two strains of Saccharomyces cerevisiae has been investigated experimentally using a batch sonication reactor equipped with a horn type sonicator and an ultrasonic processor operating at the ultrasound frequency of 20 kHz. The results have shown that the rate of release of protein is directly proportional to the frequency of the emitter surface and the square of the amplitude of oscillations and strongly depends on the sonication reactor geometry. The model based on the Helmholtz equation has been used to predict spatial distribution of acoustic pressure in the sonication reactor. Effects of suspension volume, horn tip position, vessel diameter and amplitude of ultrasound waves on the spatial distribution of pressure amplitude have been simulated. A strong correlation between the rate of protein release and the magnitude of acoustic pressure and its spatial distribution has been observed. This shows that modeling of acoustic pressure is useful for optimization of sonication reactor geometry.

A new method measuring of mass in electronic system of scales has been described. The main element of this system is inductive measuring load cell, which was compared with strain gauge load cell. The aim of the paper is described advantages of the inductive measuring system of mass and explain some main problems of this system. Digital correction of the mechanical errors of the beam like: hysteresis, creep material of the beam under constant load, influence of ambient temperature was described.

Owing to the dramatic change in the thermal conductivity of 4He when its temperature crosses the transition of superfluid (HeI) and normalfluid (HeII), a sealed-cell with a capillary is used to realize the lambda transition temperature, Tλ. A small heat flow is controlled through the capillary of the sealed-cell so as to realize the coexistence of HeI and HeII and maintain the stay of HeI/HeII interface in the capillary. A stable and flat lambda transition temperature "plateau" is obtained. Because there is a depression effect of Tλ caused by the heat flow through the capillary, a series of heat flows and several temperature plateaus are made and an extrapolation is applied to determine Tλ with zero heat flow. A rhodium-iron resistance thermometer with series number A34 (RIRT A34) has been used in 24 Tλ -realization experiments to derive Tλ with a standard deviation of 0.022mK, which proves the stability and reproducibility of Tλ.

Hydrogen is the fuel of the future, therefore many hydrogen production methods are developed. At present, fuel cells are of great interest due to their energy efficiency and environmental benefits. A brief review of effective formation methods of hydrogen was conducted. It seems that hydrogen from steam reforming of methanol process is the best fuel source to be applied in fuel cells. In this process Cu-based complex catalysts proved to be the best. In presented work kinetic equations from available literature and catalysts are reported. However, hydrogen produced even in the presence of the most selective catalysts in this process is not pure enough for fuel cells and should be purified from CO. Currently, catalysts for hydrogen production are not sufficiently active in oxidation of carbon monoxide. A simple and effective method to lower CO level and obtain clean H2 is the preferential oxidation of monoxide carbon (CO-PROX). Over new CO-PROX catalysts the level of carbon monoxide can be lowered to a sufficient level of 10 ppm.