The general standards and guidelines recommendations for PCC suggest alternating conditions of curing: starting with wet conditions for effective hydration of Portland cement followed by air-dry conditions for polymer hardening. The often accepted curing regime of PCC covers 5 days of wet curing and then the air-dry curing but it is not the optimum one. The aim of the investigation was to find the best scenario for PCC with two types of polymer modifiers: two-component epoxy resin and water dispersion of polyacrylates. The following exploitation properties were accepted as the criteria of evaluation of PCC curing effectiveness: compressive strength, tensile splitting strength, surface tensile strength (by pull-off method), wear resistance, water penetration under pressure and resistance to carbonation. The optimum time of PCC wet curing is possibly between 7 and 14 days, however, it have to be verified experimentally for specific PCC composition.

Elaborating composites containing waste materials requires study of basic mechanical properties and assessment of their structure quality. The subject of investigation was PPC concrete where aggregate was substituted with PET remaining after beverages bottles grinding. Substitution was done up to 25% (by volume). Waste material was fractioned and applied in various granulations. The main goal was to indicate the influence of such modification on the composite mechanical properties and to examine composite structure quality at macro level. Since PET and quartz differ greatly in density, to perform such examination it was possible to apply the nondestructive ultrasonic method, one of the most common NDT techniques used in material science and industry. The paper presents the effects of substitution of quartz with PET on ultrasonic wave propagation in PCC. The ultrasonic test results (measurements of wave velocity) compared with results of destructive tests (flexural and compressive strength) showed great correlation.

The concept of sustainability requires that waste-modified materials also demonstrate adequate sustainability. This paper examines the effect of modifying cement concrete with waste lime dust on the course of concrete carbonation. The waste dust comes from the dedusting of aggregate for use in HMA – Hot Mixture Asphalt. The aim of the study was to examine whether the partial replacement of sand with waste powder would have a negative effect on the potential durability of a reinforced concrete element made of this concrete. To determine the extent of carbonation, an experimental plan was prepared including the execution of concretes with varying levels of substitution and a variable water/cement ratio. In order to identify long term influence the test was performed as indicated in EN 12390-12, but with the test time extended to 560 days. The results obtained were statistically analysed and the predicted maximum extent of carbonation depending on the level of substitution and the water/cement ratio was determined. The analysis indicates that it is possible to substitute sand with waste limestone dust without having a negative impact on the extent of carbonation, and thus on the durability of the reinforced concrete structure.

Over the course of operation, asphalt road pavements are subjected to damage from car traffic loads and environmental factors. One of the possible methods of strengthening damaged asphalt pavements may be the application of an additional rigid layer in the form of a cement concrete slab with continuous reinforcement.

This paper presents a material-technological and structural solution for composite pavement where a cement concrete slab with continuous HFRP bar reinforcement is used for strengthening. Based on laboratory tests, the serviceability of composite bar reinforcement of rigid pavement slabs was shown. A design for strengthening asphalt pavement with a concrete slab with steel bar and corresponding HFRP bar reinforcement was developed. The composition of a pavement cement concrete mix was designed, and experimental sections were formed. Based on laboratory tests of samples collected from the surfaces of experimental sections and the diagnostic tests carried out in “in situ” conditions, the authors will try, in the nearest future (Part II: In situ observations and tests), to confirm the effectiveness of strengthening asphalt pavements with cement concrete slabs with HFRP components.

Pavements made of cement concrete, used for road constructions, are damaged during use. This applies to both the pavements of rural and forest roads with very low traffic loads, as well as road pavements with high traffic loads. One of the most effective ways of repairing damaged concrete cement pavements is through placing an asphalt overlay on a concrete slab. In order to increase the fatigue life of the asphalt overlay, asphalt mixtures are modified with fibres. One technological solution is to use FRP (Fiber Reinforced Polymer), an innovative material with improved properties.

The aim of this paper is to assess the impact of asphalt overlays modified with a new type of fibres to strengthen the durability of weakened cement concrete pavement structures.

On the basis of the conducted analyses, it was shown that the use of an asphalt layer reinforcement increases fatigue life, for both 15 cm thick prefabricated slabs and a typical road pavement for average traffic made of 25 cm doweled and anchored concrete slabs. There was a significant increase in the fatigue life of the concrete pavement structure as a result of modifying the overlaid asphalt mixture with FRP fibres.