Applied sciences

Chemical and Process Engineering: New Frontiers

Content

Chemical and Process Engineering | 2012 | No 1 March

Download PDF Download RIS Download Bibtex

Abstract

The kinetics of the reaction between CO2 and methyldiethanolamine in aqueous solutions have been studied using the stopped-flow technique at 288, 293, 298 and 303 K. The amine concentration ranged from 250 to 875 mol·m-3. The overall reaction rate constant was found to increase with amine concentration and temperature. The acid base catalysis mechanism was applied to correlate the experimentally determined kinetic data. A good agreement between the second order rate constants for the CO2 reaction with MDEA computed from the stopped-flow data and the values reported in the literature was obtained.

Go to article

Authors and Affiliations

Hanna Kierzkowska-Pawlak
Marta Siemieniec
Andrzej Chacuk
Download PDF Download RIS Download Bibtex

Abstract

In the study a new proposal of convective velocity determination necessary for eddy size determination from the dissipative range in a turbulent flow in a mixer was made. The proposed quantity depends on all the mean and fluctuating velocity components. By applying convective velocity one may determine the distribution of time and linear Taylor microscale in a stirred vessel.

Go to article

Authors and Affiliations

Tomasz Kurasiński
Czesław Kuncewicz
Jacek Stelmach
Download PDF Download RIS Download Bibtex

Abstract

The study was aimed to determine the hydrodynamic of water seepage through a porous bed saturated with different amounts of high viscosity liquids. An attempt was made to describe the process of seepage through beds saturated with oils using the theory of outflow of a liquid from the tank. It was assumed that the discharge coefficient will represent changes of flow resistance during the process. It was found that the dependence of this factor on time is linear. In the second part of this work kinetics of the seepage process was investigated. Dependence of oil concentrations, eluted from the deposit with the flowing water, on time has been evaluated. Thanks to these studies it was possible to determine the effectiveness of an elution of high viscosity liquids from porous beds using water as the washing out liquid.

Go to article

Authors and Affiliations

Jerzy Sęk
Mariola Błaszczyk
Michał Bartos
Download PDF Download RIS Download Bibtex

Abstract

The effective diffusivity of water in brown coal of Bełchatów mine was experimentally determined. The experiments were performed in superheated steam at 200°C and atmospheric pressure using slightly compressed pellets of cylindrical shape. The drying and temperature curves of the sample were used to identify diffusivity. An inverse problem was formulated and solved by the finite element method for 3D axially symmetric cylindrical geometry of the sample. A satisfactory fit of the simulated curves to experimental results was obtained. The obtained dependence of effective diffusivity on moisture content and temperature may be used in designing lignite dryers.

Go to article

Authors and Affiliations

Zdzisław Pakowski
Robert Adamski
Stanisław Kwapisz
Download PDF Download RIS Download Bibtex

Abstract

CFD technique was used to determine the effect of a stent-graft spatial configuration and hematocrit value on blood flow hemodynamic and the risk of a stent-graft occlusion. Spatial configurations of an endovascular prosthesis placed in Abdominal Aortic Aneurysm (AAA) for numerical simulations were developed on the basis of AngioCT data for 10 patients. The results of calculations showed that narrows or angular bends in the prosthesis as well as increased hematocrit affects blood flow reducing velocity and WSS which might result in thrombus development.

Go to article

Authors and Affiliations

Andrzej Polańczyk
Marek Podyma
Ludomir Stefańczyk
Ireneusz Zbiciński
Download PDF Download RIS Download Bibtex

Abstract

The aim of the study was the implementation of a numerical simulation of the air-water two-phase flow in the minichannel and comparing results obtained with the values obtained experimentally. To perform the numerical simulations commercial software ANSYS FLUENT 12 was used. The first step of the study was to reproduce the actual research installation as a three-dimensional model with appropriate and possible simplifications - future computational domain. The next step was discretisation of the computational domain and determination of the types of boundary conditions. ANSYS FLUENT 12 has three built-in basic models with which a two-phase flow can be described. However, in this work Volume-of-Fluid (VOF) model was selected as it meets the established requirements of research. Preliminary calculations were performed for a simplified geometry. The calculations were later verified whether or not the simplifications of geometry were chosen correctly and if they affected the calculation. The next stage was validation of the chosen model. After positive verification, a series of calculations was performed, in which the boundary conditions were the same as the starting conditions in laboratory experiments. A satisfactory description of the experimental data accuracy was attained.

Go to article

Authors and Affiliations

Jarosław Sowiński
Marek Krawczyk
Marek Dziubiński
Download PDF Download RIS Download Bibtex

Abstract

Biosynthesis of lovastatin (a polyketide metabolite of Aspergillus terreus) in bioreactors of different working volume was studied to indicate how the change of scale of the process influences the formation of this metabolite. The experiments conducted in shake flasks of 150 ml working volume allowed to obtain lovastatin titres at the level of 87.5 mg LOV l-1, when two carbon sources, namely lactose and glycerol were used. The application of the same components in a large stirred-tank bioreactor of 5.3-litre working volume caused a decrease of lovastatin production by 87% compared to the shake flask culture. The deficiency of nitrogen in this bioreactor did not favour the formation of lovastatin, in contrast to the small bioreactor of 1.95-litre working volume, in which lovastatin titres comparable to those in the shake flasks could be achieved, when organic nitrogen concentration was two-fold decreased. When the control of pH and/or pO2 was used simultaneously, an increase in lovastatin production was observed in the bioreactors. However, these results were still slightly lower than lovastatin titres obtained in the shake flasks.

Go to article

Authors and Affiliations

Marta Pawlak
Stanisław Ledakowicz
Marcin Bizukojć
Download PDF Download RIS Download Bibtex

Abstract

Results for microcrystalline cellulose pyrolysis are presented, which includes thermogravimetric measurements and kinetic analysis of experimental data. The effect of sample mass size and heating rate on estimated values of activation energy and pre-exponential factor is demonstrated and a simple modification of procedure is proposed that allows for the correct values of kinetic parameters regardless of the experimental conditions. The efficiency of the proposed method is confirmed for two endothermic chemical reactions. A method of nonlinear regression is used for calculation of kinetic parameters for a single or TG curve or several curves simultaneously.

Go to article

Authors and Affiliations

Lech Nowicki
Maciej Markowski
Download PDF Download RIS Download Bibtex

Abstract

An analysis of the effect of feed foaming on the efficiency of sunflower oil encapsulation on selected product properties is presented in the paper. Experiments were carried out in a pilot-plant concurrent spray dryer using the gas-admixing technique. The analysis of the product properties showed that the application of foaming makes it possible to control final product properties, e.g. apparent density, bulk density, distribution of particle diameters, etc. at a high efficiency of sunflower oil encapsulation.

Go to article

Authors and Affiliations

Artur Lewandowski
Marcin Czyżewski
Ireneusz Zbiciński
Download PDF Download RIS Download Bibtex

Abstract

In the last decade a growing interest was observed in low-cost adsorbents for heavy metal ions. Clinoptilolite is a mineral sorbent extracted in Poland that is used to remove heavy metal ions from diluted solutions. The experiments in this study were carried out in a laboratory column for multicomponent water solutions of heavy metal ions, i.e. Cu(II), Zn(II) and Ni(II). A mathematical model to calculate the metals' concentration of water solution at the column outlet and the concentration of adsorbed substances in the adsorbent was proposed. It enables determination of breakthrough curves for different process conditions and column dimensions. The model of process dynamics in the column took into account the specificity of sorption described by the Elovich equation (for chemical sorption and ion exchange). Identification of the column dynamics consisted in finding model coefficients β, KE and Deff and comparing the calculated values with experimental data. Searching for coefficients which identify the column operation can involve the use of optimisation methods to find the area of feasible solutions in order to obtain a global extremum. For that purpose our own procedure of genetic algorithm is applied in the study.

Go to article

Authors and Affiliations

Elwira Tomczak
Władysław Kamiński
Download PDF Download RIS Download Bibtex

Abstract

The paper presents the results of studies on quartzite milling in a ball mill. The milling was conducted in a batch system, for diversified compositions of balls. The milling product was subjected to granulometrical, morphological and strength analyses. On the basis of the developed Reid's theory and using the Austin-Gardner equation, a form of the function circumscribing the specific rate of comminution of selected size fractions was determined. The values of the breakage rate function bi, j for the mill's apparatus conditions were determined. The impact was investigated for a variable number of grinding media contact points on the values of specific rate S and the values of the breakage rate function bi, j. Furthermore, the values of coefficients occurring in the equations circumscribing the specific rate of milling S and breakage parameter bi, j were determined.

Go to article

Authors and Affiliations

Tomasz Olejnik
Download PDF Download RIS Download Bibtex

Abstract

The article focuses on multicomponent system separation with the use of an innovative membrane-based technique i.e. pervaporation. Pervaporation is a membrane technique for separation of liquid mixtures on solid nonporous membranes. Pervaporation is used in this study to separate a quaternary system acetone-butanol-ethanol-water. Such a system may be derived from ABE fermentation process, and the resulting product, biobutanol, is a potential biofuel and may be used in internal combustion engines.

Experiments in the study involving concentration of butanol by pervaporation were performed using PERVAP 4060 flat-sheet commercial membrane. To describe the PV process a semi-empirical approach was used. As a result of experiments and calculations permeance coefficients were obtained. Separation and permeance factors were calculated to assess the efficiency of the system separation. Beforehand, activity coefficients were determined for all the components of the mixture with the NRTL equation. Separation coefficients for all the components differed depending on process parameters: concentration, feed flow rate and process temperature. The study confirmed the separation effect of the quaternary system. The most interesting results were obtained for the concentration of butanol. Pervaporation allows to concentrate butanol over 10 times. The permeance coefficient reached for butanol an average value of 7.06·10-3 in comparison with the results for ethanol 3.24·10-2 and acetone 1.83·10-2 [kmol(m2h)-1]. The temperature change from 50 to 70°C led to an increased permeance factor and there was no apparent effect on it in the feed flow rate. Due to the hydrophobicity of the membrane water fluxes in the quaternary system were negative.

Go to article

Authors and Affiliations

Joanna Marszałek
Władysław Kamiński
Download PDF Download RIS Download Bibtex

Abstract

This study was aimed at evaluating the possibility to use the Friedrich-Braun fractional derivative rheological model to assess the viscoelastic properties of xanthan gum with rice starch and sweet potato starch. The Friedrich-Braun fractional derivative rheological model allows to describe viscoelastic properties comprehensively, starting from the behaviour characteristic of purely viscous fluids to the behaviour corresponding to elastic solids. The Friedrich-Braun fractional derivative rheological model has one more virtue which distinguishes it from other models, it allows to determine the relationship between stress and strain and the impact of each of them on viscoelastic properties on the tested material. An analysis of the data described using the Friedrich-Braun fractional derivative rheological model allows to state that all the tested mixtures of starch with xanthan gum form macromolecular gels exhibiting behaviour typical of viscoelastic quasi-solid bodies. The Friedrich-Braun fractional derivative rheological model and 8 rheological parameters of this model allow to determine changes in the structure of the examined starch - xanthan gum mixtures. Similarly important is the possibility to find out the trend and changes going on in this structure as well as their causes.

Go to article

Authors and Affiliations

Magdalena Orczykowska
Marek Dziubiński
Download PDF Download RIS Download Bibtex

Abstract

This paper presents a method for quantitative assessment of the mechanisms of nucleation and granules growth by layering in the process of bed wetting during periodic disc granulation. This study included two initial, consecutive stages of a process with defined time courses. The first phase was a time period, in which only formation of new nuclei took place, while in the second stage simultaneous nucleation and growth of granules as a result of sticking raw material grains to pre-existing nuclei occurred. Different kinds of binding liquid were used for bed wetting in each phase. In the first phase, an aqueous solution of dye was used, and pure distilled water in the second stage. The contribution of particular mechanisms to the formation of agglomerates at different time points within the second phase of the process was determined in this study. To do that the results of bed granulometric analysis, mass balance of size fractions and the analysis of contents of a marker (dye) delivered to the bed with the binding liquid during the first phase in agglomerates were used. To assess the concentration of the dye in different size fractions of the batch, spectrophotometric analysis was utilised. The study was performed using UV-VIS JASCO V-630 spectrophotometer equipped with an integrating sphere. The sieve analysis, spectrophotometric studies and mass balance were used to determine changes in the weight of the dye containing nuclei and of the nuclei containing no dye. The aforementioned analyses were also used to assess changes in the weight of formed granules and of raw material particles attached to nuclei during simultaneous nucleation and growth of granules.

Go to article

Authors and Affiliations

Andrzej Obraniak
Tadeusz Gluba
Download PDF Download RIS Download Bibtex

Abstract

A new concept of an electrostatic spray column for liquid-liquid extraction was investigated. An important problem for separation processes is the presence of azeotropic or close-boiling mixtures in their production, for example heptane with ethanol, since the separation is impossible by ordinary distillation. The use of ionic liquids (IL) as a dispersed solvent specially engineered for any specific organic mixture in terms of selectivity is a key factor to successful separation. As IL present particularly attractive combination of favorable characteristics for the separation of heptane and ethanol, in this work we use 1-butyl-3-methylimidazolium methyl sulfate [BMIM][MeSO4]. Because of high viscosity and relatively high cost of IL a new technique was introduced, consisting in the electrostatically spray generation to enhance the mass transport between the phases. In order to optimally design the geometry of the contactor a series of numerical simulation was performed. Especially multi-nozzle variants for better exploitation of contactor volume were investigated. Experiments showed excellent possibility of control of the dispersion characteristics by applied voltage and thus control of the rate of extraction. The preliminary simulations based on our mathematical model for a three nozzle variant exhibited visual agreement with the theory of electrostatics.

Go to article

Authors and Affiliations

Marek Krawczyk
Kamil Kamiński
Jerzy Petera
Download PDF Download RIS Download Bibtex

Abstract

Results of the investigation of thermal degradation of polyolefins in the laboratory-scale set-up reactors are presented in the paper. Melting and cracking processes were carried out in two different types of reactors at the temperature of 390-420°C. This article presents the results obtained for conversion of polyolefin waste in a reactor with a stirrer. Next, they were compared with the results obtained for the process carried out in a reactor with a molten metal bed, which was described in a previous publication. For both processes, the final product consisted of a gaseous (2-16 % mass) and a liquid (84-98 % mass) part. No solid product was produced. The light, "gasoline" fraction of the liquid hydrocarbons mixture (C4-C10) made up over 50% of the liquid product. The overall (vapor) product may be used for electricity generation and the liquid product for fuel production.

Go to article

Authors and Affiliations

Marek Stelmachowski
Krzysztof Słowiński

Instructions for authors

All manuscripts submitted for publication in Chemical and Process Engineering: New Frontiers must comprise a description of original research that has neither been published nor submitted for publication elsewhere.

The content, aim and scope of the proposals have to comply with the main topics of the journal, i.e. discuss at least one of the four main areas, namely:
• New Advanced (Nano) Materials
• Environment & Water Processing (including circular economy)
• Biochemical & Biomedical Engineering (including pharmaceuticals)
• Climate & Energy (including energy conversion & storage, electrification, decarbonization)

Chemical and Process Engineering: New Frontiers publishes: i) experimental and theoretical research papers, ii) short communications, iii) critical reviews, and iv) perspective articles. Each publication form is peer-reviewed by at least two independent referees.

New Submissions

Manuscripts are submitted for publication via Editorial System. When writing a manuscript, you may choose to submit it as a single Word file to be used in the refereeing process. The manuscript needs to be written in a clear way. The minimum requirements are:
• Please use clear fonts, at least 12 points large, with at least 1.5-line spacing.
• Figures should be placed in relevant places within the manuscript. All figures and tables should be numbered and provided with appropriate caption and legend, if necessary.


Language requirements

• Use Simple Past to talk about your experiment and your results as they were finished before you wrote the paper. Use Simple Past to describe what you did.
Example: Two samples were taken. Temperature increased to 200K at the end of the process.
• Use Simple Present to refer to figures and tables.
Example: Table 2 shows nitrogen concentration changes in the process.
• Use Simple Present to talk about your conclusions. You move here from describing your results to stating what is generally true.
Example: The process is caused by changes of nitrogen concentration.
• Capitalise words like ‘Table 2’, ‘Equation 11’.
• If a sentence is longer than three lines, break down your writing into logically divided parts (paragraphs). Start a new paragraph to discuss a new concept.
• Check noun/verb agreement (singular/plural).
• It is fine to choose either British or American English but you should avoid mixing the two.
• Avoid empty language (it is worth pointing out that, etc.).



Revised Submission

After the first revision, authors will be requested to put their paper in the correct format, using the below guidelines and template for articles.


Manuscript outline

1. Header details
a. Title,
b. Names (first name and further initials) and surnames of authors,
c. Institution(s) (affiliation),
d. Address(es) of authors,
e. ORCID number of all authors.
f. Information about the corresponding author: name and surname, email address.

2. Abstract – should contain a short summary of the proposed paper. In the maximum of 200 words the authors should present the main assumptions, results and conclusions drawn from the presented study.

3. Keywords – up to 5 characteristic keyword items should be provided.

4. Text
a. Introduction. In this part, the rationale for research and formulation of the scientific problem should be included and supported by a concise review of recent literature.
b. Main text. It should contain all important elements of the scientific investigations, such as presentation of experimental setup, mathematical models, results and their discussion. This part may be divided into the following sections: Methods, Results, Discussion.
c. Conclusions. The major conclusions can be put forward in a concise style in a separate chapter. A presentation of conclusions from the reported research work accompanied by a short commentary is also acceptable.
d. Figures: drawings, diagrams and photographs can be in colour and should be located in appropriate places in the manuscript. Their form should be of a vector or raster type with the minimum resolution of 900 dpi. In addition, all figures, including drawings, graphs and photos should be uploaded in a separate file via Editorial System in one of the following formats: bmp, tiff, jpg or eps. For editorial reasons, graphic elements created with MS Word or Excel will not be accepted. They should be saved as image files in the source program. Screen shots will not be accepted. The basic font size of letters used in figures should be at least 10 pts after adjusting graphs to the final size.
e. Tables should be made according to the format shown in the template.
f. All figures and tables should be numbered and provided with an appropriate caption and legend, if necessary. They have to be properly referenced to and commented in the text of the manuscript.

5. List of symbols should be accompanied by their units

6. Acknowledgements may be included before the list of literature references

7. Literature citations
The method of quoting literature source in the manuscript depends on the number of its authors:
single author – their surname and year of publication should be given, e.g. Marquardt (1996) or (Marquardt, 1996),
two authors – the two surnames separated by the conjunction “and” with the publication year should be given, e.g. Charpentier and McKenna (2004) or (Charpentier and McKenna, 2004),
three and more authors – the surname of the first author followed by the abbreviation “et al.” and year of publication should be given, e.g. Bird et al. (1960) or (Bird et al., 1960).

In the case of citing more sources in one bracket, they should be listed in alphabetical order using semicolon for separation, e.g. (Bird et al., 1960; Charpentier and McKenna, 2004; Marquardt, 1996). Should more citations of the same author(s) and year appear in the manuscript then letters “a, b, c, ...” should be successively applied after the publication year.

Bibliographic data of the quoted literature should be arranged at the end of the manuscript in alphabetical order of surnames of the first author. It is obligatory to indicate the DOI number of those literature items, whose numbers have already been assigned. Journal titles should be specified by typing their right abbreviations or, when in doubts, according to the Science and Engineering Journal Abbreviations.

Examples of citation for:

Articles
Charpentier J. C., McKenna T. F., 2004. Managing complex systems: some trends for the future of chemical and process engineering. Chem. Eng. Sci., 59, 1617-1640. DOI: 10.1016/j.ces.2004.01.044.
Information from books (we suggest adding the page numbers where the quoted information can be found)
Bird R. B., Stewart W.E., Lightfood E.N., 2002. Transport Phenomena. 2nd edition, Wiley, New York, 415-421.
Chapters in books
Hanjalić K., Jakirlić S., 2002. Second-moment turbulence closure modelling, In: Launder B.E., Sandham N.D. (Eds.), Closure strategies for turbulent and transitional flows. Cambridge University Press, Cambridge, 47-101.
Conferences
ten Cate A., Bermingham S.K., Derksen J.J., Kramer H.M.J., 2000. Compartmental modeling of an 1100L DTB crystallizer based on Large Eddy flow simulation. 10th European Conference on Mixing. Delft, the Netherlands, 2-5 July 2000, 255-264.



Cover letter


Authors are kindly asked to provide a cover letter which signifies the novelty and most important findings of the manuscript as well as the significance to the field.


Author contributions

During submission, authors will be asked to provide the individual contributions to the paper using the relevant CRediT roles: Conceptualization; Data curation; Formal analysis; Funding acquisition; Investigation; Methodology; Project administration; Resources; Software; Supervision; Validation; Visualization; Roles/Writing - original draft; Writing - review & editing.


Suggested Reviewers

Authors are kindly requested to include a list of 4 potential reviewers for their manuscript, with complete contact information. Suggested reviewers may not reside in the same country as the corresponding author and remain subject to the Editors' discretion in appointing manuscripts for review.


Payments

Starting from 2014 a principle of publishing articles against payment is introduced, assuming non-profit making editorial office. According to the principle, authors or institutions will have to cover the expenses amounting to 1500 PLN netto (excl. VAT) per published article. The above amount will be used to supplement the limited financial means received from the Polish Academy of Sciences for the editorial and publishing expenses. The method of payment will be indicated in an invoice sent to the authors or institutions after acceptance of their manuscripts to be published.

Publication Ethics Policy

ETHICAL PRINCIPLES

Editors of the "Chemical and Process Engineering: New Frontiers" pay attention to maintain ethical standards in scientific publications and undertake any possible measure to counteract neglecting the standards. Papers submitted for publication are evaluated with respect to reliability, conforming to ethical standards and the advancement of science. Principles given below are based on COPE's Best Practice Guidelines for Journal Editors, which may be found at:
http://publicationethics.org/files/u2/Best_Practice.pdf

Authors’ duties

Authorship
Authorship should be limited to persons, who markedly contributed to the idea, project, realization and interpretation of results. All of them have to be listed as co-authors. Other persons, who affected some important parts of the study should be listed or mentioned as co-workers. Author should be certain that all co-authors were enlisted, saw and accepted final version of the paper and agreed upon its publication.

Disclosure and conflict of interests
Author should disclose all sources of financing of his/her study, the input of scientific institutions, associations and other subjects and all important conflicts of interests that might affect results and interpretation of the study.

Standards in reporting
Authors of papers based on original studies should present precise description of performed work and objective discussion on its importance. Source data should be accurately presented in the paper. The paper should contain detailed information and references that would enable others to use it. False or intentionally not true declarations are not ethical and are not accepted by the editors.

Access to and storage of data
Authors may be asked for providing raw data used in the paper for editorial assessment and should be prepared to store them within the reasonable time period after publication.

Multiple, unnecessary and competitive publications
As a rule author should not publish papers describing the same studies in more than one journal or primary publication. Submission of the same paper to more than one journal at the same time is not ethical and prohibited.

Confirmation of sources
Author should cite papers that affected the creation of submitted manuscript and every time he/she should confirm the use of other authors’ work.

Important errors in published papers
When author finds an important error or inaccuracy in his/her paper, he/she is obliged to inform Editorial Office about this as soon as possible.

Originality and plagiarism
Author may submit only original papers. He/she should be certain that the names of authors referred to in the paper and/or fragments of their texts are properly cited or mentioned.

Ghostwriting
Ghost writing/guest authorship are manifestation of scientific unreliability and all such cases will be revealed including notification of appropriate subjects. Signs of scientific unreliability, especially violation of ethical principles in science will be documented by the Editorial Office.


Duties of the Editorial Office


Editors’ duties
Editors know the rules of journal editing including the procedures applied in case of uncovering non-ethical practices.

Decisions on publication
Editor-in Chief is obliged to apply present legal status as to defamation, violation of author’s rights and plagiarism and bears the responsibility for decisions. He/she may consult thematic editors and/or referees in that matter.

Selection of referees
Editorial Office provides appropriate selection of referees and takes care about appropriate course of peer –reviewing (the review has to be substantive).

Confidentiality
Every member of editorial team is not allowed to disclose information about submitted paper to any person except its author, referees, other advisors and editors.

Discrimination
To counteract discrimination the Editorial Office obeys the legally binding rules.

Disclosure and conflict of interests
Not published papers or their fragments cannot be used in the studies of editorial team or ref-erees without written consent of the author.


Referees' duties

Editorial decisions

Referee supports Editor-in-Chief in taking editorial decisions and may also support author in improving the paper.

Back information
In case a selected referee is not able to review the paper or cannot do it in due time period, he/she should inform secretary of the Editorial Office about this fact.

Objectivity standards
Reviews should be objective. Personal criticism is inappropriate. Referees should clearly ex-press their opinions and support them with proper arguments.

Confidentiality
All reviewed papers should be dealt with as confidential. They should not be discussed or revealed to persons other than the secretary of the Editorial Office.

Anonymity
All reviews should be made anonymously and the Editorial Office does not disclose names of the authors to referees.

Disclosure and conflict of interests
Confidential information or ideas resulting from reviewing procedure should be kept secret and should not be used to gain personal benefits. Referees should not review papers, which might generate conflict of interests resulting from relationships with the author, firm or institution involved in the study.

Confirmation of sources
Referees should indicate publications which are not referred to in the paper. Any statement that the observation, source or argument was described previously should be supported by appropriate citation. Referee should also inform the secretary of the Editorial Office about significant similarity to or partial overlapping of the reviewed paper with any other published paper and about suspected plagiarism.



This page uses 'cookies'. Learn more